User manual FUTABA 2PHKA

[. . . ] Thank you for purchasing a Futaba 2PH/2PHKA. Before using your 2PH/2PHKA, read this manual carefully and use your R/C set safely. After reading this manual, store it in a safe place. APPLICATION, EXPORT, AND RECONSTRUCTION 1. This product may be used for models only. [. . . ] For example if you only make two run in a day or you regularly use a small amount of the batteries capacity, the memory effect can reduce the actual capacity even if the battery is charged for the recommended amount of time. Prohibited Do not throw a Ni-cad battery into a fire. Do not disassemble or attempt to repair a Nicad battery pack. Overheating, damage and acid leakage may lead to burns, loss of eye sight as well as numerous other types of injuries. The electrolyte in Ni-cad batteries is a strong alkali. Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub, wash immediately with water, seek medical attention at once. If electrolyte comes in contact with your skin or clothes, wash with water immediately. Caution Prohibited Do not store your R/C system where it will be exposed to the following conditions. · Extreme heat or coldness · Exposed to direct sunlight · Where humidity is high · Where vibration is prevalent · Where dust is prevalent · Where there is steam and condensation · Where the system would be exposed to engine exhaust Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation. (When using a Ni-cad battery to power your system) Caution When disposing Ni-cad batteries, cover any exposed contacts with some type of insulation to prevent short circuit. *If the Red led flashes, replace batteries. Steering Wheel *Turn model to left or right. Steering Trim (P13) Power Switch *When slid upward, the power is turned on. Throttle Trim (P13) *Adjusts the throttle in small increments so the model will not move at neutral. Trim Panel Cover *Open the cover by sliding it to the left. ¥ Servo Reversing Switch (P13) ¥ Steering EPA (only 2PHKA) (P14) ¥ Throttle EPA (only 2PHKA) (P14) ¥ Steering D/R (only 2PHKA) (P14) Throttle Trigger *Control the speed of the model and movement forward and backward. Grip Handle (T2PHKA) Applicable motors (Number of turns is criteria. ) E. S. C. MC230CR / MC330CR ·Use the MC230CR with a motor with 20T or more turns. ·Use the MC330CR with a motor with 13T or more turns. *If a motor with a number of turns smaller than the above is used, the heat protector and overcurrent protection circuit may operate. The number of turns of the motor is a criteria only. Depending on the running conditions, the protection circuit may operate even if the condition above is satisfied. (Orange) (Blue) Checker LED Pushbutton switch Motor connector Connects to the motor. If the motor rotates in the wrong direction, interchange the connections of this connector. (Black) Nicd battery connector Connects to the running Nicd battery. (Black) is minus. (Red) Nicd battery 6~7 cells (7. 2~8. 4V) MC230CR Receiver connector Connects to the receiver throttle channel. Miniature screwdriver Power switch Accessory. Use to press the pushbutton switch. 7 Before Operation *Adjusts the steering in small increments so the model will run straight. Handling Procedure For Batteries (8 AA Size Batteries) (Battery Replacement Method) Caution Always be sure you reinsert the batteries in the correct polarity order. If the batteries are loaded incorrectly , the transmitter may be damaged. When the transmitter will not be used for any short or long period of time, always remove the batteries. If the batteries do happen to leak , clean the battery case and contacts thoroughly. Make sure the contacts are free of corrosion. 1 Remove the battery cover from the transmitter by sliding it in the direction of the arrow in the figure. 2 Remove the used batteries. Pay very close attention to the polarity markings and reinsert accordingly. 4 Slide the battery cover back onto the case. (Battery Disposal) Some states require special handling when any type of battery is disposed. Contact the State Agency responsible for recycling hazardous waste for procedures in your area. Before Operation 8 OPEN (Battery Alarm Display) When the Green battery level indicator (LED) goes off and the Red LED flashes, change the batteries immediately. [. . . ] (The reverse function is switched alternately. ) BRAKE/REVERSE OPERATING INSTRUCTIONS Operation can be switched to reverse operation by returning the throttle trigger (or throttle stick) from the brake position to the neutral position. PROTECTION CIRCUIT OPERATION The following protection circuits are built into the MC230CR / MC330CR. When a protection circuit operates, remove the cause before operating the model again. Overcurrent protection Heat protector Low voltage operation When an overcurrent flows due to an output short circuit, etc. , the overcurrent protection circuit automatically limits the current to protects the FET. Remove the cause of the short circuit, etc. [. . . ]