User manual FUTABA R607FS

[. . . ] Unlike 72MHz equipment, they're not as vulnerable to vibration. Using less foam lets them operate cooler -- which is a plus for all electronics. Tip: To keep the receiver cooler use small foam blocks (like standoffs) so that there is an air channel around the receiver. Shade your model from sunlight when not flying. [. . . ] · Exclusive ID code to avoid interference from other FASST systems. · Fail Safe (F/S) function (for throttle channel)-F/S, Battery F/S · Dual antenna diversity (R607FS) Usage Precautions: 1) Prior to utilizing any radio control system, it is strongly recommended that you read and abide by the Safety Code created by the Academy of Model Aeronautics as well as any site specific rules and regulations that might exist. Doing so will greatly increase your enjoyment of the hobby. 2) In order to maintain complete control of your aircraft it is important that it remains visible at all times. Flying behind large objects such as buildings, grain bins, etc. Doing so may result in the reduction of the quality of the radio frequency link to the model. 3) Please do not grasp the transmitter module's antenna during flight. Doing so may degrade the quality of the radio frequency transmission. Range Check the Radio It is extremely important to range check your models prior to each flying session. This enables you to ensure that everything is functioning as it should and to obtain maximum enjoyment from your time flying. The TM-7 transmitter module incorporates a system that reduces its power output and allows you to perform such a range check. 1 2 Turn on the transmitter. you Please make sure thatflyingdo not push and hold the F/S, Range switch when as this reduces the power output of the transmitter and reduces the overall range of your transmitter. WARNING Instruction Manual Applicable systems: T7U, T8U, T9C and T9Z After the radio frequency link has been established (as indicated by either a solid green LED or a blinking green LED), press and hold the "F/S, Range" switch located on the rear of the TM-7 transmitter module. As indicated by the blinking red LED, the radio frequency power has been reduced to allow for the range check. *Note:Donotpressandholdthe"F/S, Range"switchpriortoturning onthetransmitter. ThiswillalterthestatusoftheF/Ssettingsas notedpreviously. Inordertoavoidthissituation, pleasewaitfora Other precautions When utilizing the trainer function of the transmitter as an instructor, please do not switch to the student's control unit until the RF is active after turning the transmitter on. Failure to adhere to this procedure may result in a malfunction. Contents and Technical Specifications Your 2. 4GHz system includes the following components: FASST transmitter module, system and receiver compatibility Transmitter Receiver R606FS R607FS TM-7 Module T6EX 2. 4G System T7C 2. 4G System -- Okay Okay Okay Okay Okay If any difficulties are encountered while setting up or operating your TM-7 transmitter module and R607FS receiver, please consult this instruction manual first. For further assistance you may also refer to your hobby dealer, or contact the Futaba Service Center at the web site, fax or telephone number below: www. futaba-rc. com, www. 2. 4gigahertz. com Fax (217) 398-7721, Tel (217) 398-8970 (option 2) If you are unable to resolve the issue, pack the system in its original container with a note enclosed and a thorough, accurate description of the difficulty. Include the following in your note: · Symptoms (Including when the problem occurred) · System (transmitter, Receiver, Servos and model numbers) · Model (Model name) · Model numbers and quantity · Your Name, Address and Telephone number Send the respective items to the authorized Futaba Service Center address below: Futaba Service Center 3002 N Apollo Drive Suite 1 Champaign, IL 61822 Repair Service (in U. S. A. ) Specifications: TM-7 RF Module·Communicationsystem:one-waycommunication ·Antenna:1/2wavelengthdi-pole ·Currentconsumption:150mAmaximum ·SettingswitchforFailSafe(F/S)settingandrangecheck ·LED(lightemittingdiodes)indicatetheoperationalstatus R607FS Receiver·Dualantennadiversity ·Powerrequirement:4. 8Vor6. 0VbatteryorregulatedoutputfromESC, etc. ·F/SandBatteryF/Sfunctionforthrottlechannel(channel three) ·Size:1. 64x1. 08x0. 36in. (41. 6x27. 5x9. 2mm) ·Weight:0. 34oz. (9. 8g) *Pleasenote:TheTM-7moduleisNOTcompatiblewiththeR606FSreceiver! FCC Information To assure continued FCC compliance: (1) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC Label Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. R607FS Receiver Mini screwdriver TM-7 RF Module Special Markings; Pay special attention to the safety at the parts of this manual that are indicated by the following marks. [Symbol] ; Prohibited ; Mandatory Mark ©Copyright 2007. No part of this manual may be reproduced in any form without prior permission. The contents of this manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made. FUTABA CORPORATION Phone: (043) 296-5118 Facsimile: (043) 296-5124 Makuhari Techno Garden Bldg. , B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan ©FUTABACORPORATION2007, 07(1) Meaning Procedures which may lead to a dangerous condition and cause death or serious injury to the user if not carried out properly. [. . . ] Should you wish to re-link them, or if you have purchased a separate receiver and would like to link it to this TM-7, please adhere to the following procedure. LED indication Green Red Solid Off Blink Off Blink Status Initializing (When Power Up) Check RF condition nearby RF power on RF power on (Power reduced to perform the range check function) RF power on RF power on (Power reduced to perform the range check function) Fail safe (F/S) ----Off Off On On setting F/S function it make Whenthat theretheno other FASST is importantintothe ON sure is Air System position nearby. WARNING 4 5 Solid Solid Solid Blink Blink If your model includes metal conductive items which may impact the receiver's ability to clearly receive the radio frequency signal, we suggest mounting the receiver so that the receiver antennas exit both sides of the model. This will allow the best radio frequency signal condition at any flying attitude. Ensure that the antennas are at least 1/2" away from any conductive materials such as metal and carbon. Please note: this is not applicable to the coaxial portion of the antenna. [. . . ]