User manual FUTUBA 10CP

[. . . ] 10CAP/10CHP/10CP 10-CHANNEL RADIO CONTROL SYSTEM INSTRUCTION MANUAL Technical updates and additional programming examples available at: http://www. futaba-rc. com/faq Entire Contents ©Copyright 2008 1M23N21003 TABLE OF CONTENTS Linear, Prog. mixes 1-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mixes 5-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Types: · Linear: Most mixes are linear. A 100% linear mix tells the slave servo to do exactly what the master servo is doing, using 100% of the slave channel's range to do so. An example is FLAPERON to move exactly the same amount. A 50% linear mix would tell the slave servo, for example, to move to 50% of its range when the master's control is moved 100%. 52. ) · Offset: An OFFSET servo is moved a set percent of its range. An example of this is AIRBRAKE · Curve: Curve mixes are mostly used in helicopters, but may also be used in airplanes and gliders. An example is THROTTLE-NEEDLE mixing, where the in-flight needle's servo is moved, changing the mixture, as the throttle servo is moved. 65. ) · Delay: Delay mixes are part of a few very special functions that make the servo move to its desired range more slowly. THROTTLE DELAY (simulates turbine engines, p. 66) and the elevator delay in AIRBRAKE are two examples of this (see p. 103) is another example that slows the servo movement to the trim settings for the other conditions. to use. Additionally, the 10C ACRO and GLID programs both provide 4 linear and 4 curve fully-programmable mixes (HELI provides 4 linear and 2 curve) that allow you to set up special mixes to resolve flight difficulties, activate additional functions, etc. Let's look quickly at a few examples that are features we've already covered. This may help to clarify the mix types and the importance of mixes. Additional examples: · Exponential is a preprogrammed curve mix that makes the servos' response more (+) or less (-) sensitive around center stick (works in conjunction with dual rate, a linear mix that adjusts the total range). · IDLE-DOWN and THR-CUT are two OFFSET pre-programmed mixes. These tell the throttle servo, when below a certain point, to move toward idle an additional set percentage to help close the carburetor. · ELEV-TO-FLAP model loop even tighter than it can on elevator alone. 62. ) · THROTTLE-NEEDLE mixing is a curve mix (like PROG. MIX 5 to 8 · THROTTLE DELAY mixing is a pre-programmed delay mix that slows down the response of the CH3 servo. 66. ) Next, we'll get an in-depth look at some pre-programmed mixes ( simplicity) we've not covered yet, and last, look at the fully-programmable mix types. 61 ELEV-FLAP mixing (ACRO GLID): ELEV-FLAP ELEVATOR STICK is moved. It is most commonly used to make tighter pylon turns or squarer corners in maneuvers. In (ACRO) Adjustability: · Rate when the ELEVATOR STICK is pulled to provide full up elevator. ) · Switch: fully assignable. [. . . ] 96 118 Throttle trim adjustment: see ATL to change throttle trim from "idle only" to full trim control like all other channels. See THR-REV to reverse THROTTLE STICK completely, including moving trim to the top of the THROTTLE STICK. See also Idle management for details on idle down and throttle cut functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]