User manual FUTUBA 12Z

[. . . ] 12Z 12 CHANNEL RADIO CONTROL SYSTEM PCMG3/PCM1024/FM selectable INSTRUCTION MANUAL 1M23N16902 TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] º *For this curve, [Linear] curve type can be used and the entire curve can be lowered with the [Offset] function. <Model Basic Setting Procedure> 41 º *For this curve, [Linear] curve type can be used and the entire curve can be lowered with the [Offset] function. 11. Throttle cut setting Throttle cut provides an easy way to stop the at idle. The action is not functional at high throttle to avoid accidental dead sticks. The switch's location and direction must be chosen, as it defaults pitch interaction swash plate in the aileron (roll) direction and elevator (cyclic pitch) corresponding to each operation of each condition. *With throttle stick at idle, adjust the cut position until the engine consistently shuts off, but throttle linkage is not binding. When finished, push the RPM loss caused by swash operation at aileron or elevator operation can be corrected with the clockwise and counterclockwise torque is applied when pirouetting can also be corrected. 10. Gyro sensitivity and mode switching The gyro sensitivity and mode switching Menu, and can be set for each condition. 42 <Model Basic Setting Procedure> Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below. Always read [Precautions when mounting the receiver and servos] of [Before using]. When mounting the receiver and servos to the fuselage, connect the necessary points in accordance with the kit instruction manual. Receiver and servos connection diagram ~ ~ Ni-Cd battery Charging port/ DSC connector Receiver switch Servos The Servo connection by model type tables are shown on the following pages. Connect the servos to match the fuselage used. <Model Basic Setting Procedure> 43 Servo connection by model type The T12Z transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. The channel assignment (initial setting) for each model type is shown below. Connect the receiver and servos to match the type used. *The set channels can be checked at the Function screen of the Linkage Menu. The channel assignments can also be changed. For more information, read the description of the Function menu. Airplane/glider/motor glider 1AIL RX CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 Airplane Glider EP Airplane 2AIL Glider EP 2AIL+1FLAP Airplane Glider EP 2AIL+2FLAP Airplane Glider EP Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Throttle Gear AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 Motor AUX7 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 Throttle Motor AUX1 Throttle Motor AUX7 Throttle Motor AUX6 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron AUX7 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Gear AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX7 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX7 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Flap Gear AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 Flap AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Flap AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Gear Flap Flap2 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX5 Flap Flap2 AUX4 AUX3 AUX2 AUX1 AUX5 Flap Flap2 AUX4 AUX3 AUX2 AUX1 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 Airbrake Airbrake Airbrake AUX1 Camber Camber Camber Camber Camber Camber Camber Camber Camber 2AIL+4FLAP RX CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 Airplane Glider EP 4AIL+2FLAP Airplane Glider EP 4AIL+4FLAP Airplane Glider EP Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Throttle Motor AUX4 Throttle Motor AUX4 Throttle Motor AUX2 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Gear Flap Flap2 Flap3 Flap4 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX3 Flap Flap2 Flap3 Flap4 AUX2 AUX1 AUX3 Flap Flap3 Flap4 AUX2 AUX1 Gear AUX3 AUX3 Gear AUX1 AUX1 Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Flap1 Flap2 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 Flap3 Flap4 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 Flap1 Flap2 Flap3 Flap4 Flap1 Flap2 Flap3 Flap4 Flap2 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Camber Camber Camber Camber Camber Camber Camber Camber Camber 44 <Model Basic Setting Procedure> 1AIL RX CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 Glider Airplane EP Airplane 2AIL Glider EP 2AIL+1FLAP Glider Airplane EP 2AIL+2FLAP Glider Airplane EP Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Throttle Motor AUX7 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Motor AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX7 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Throttle Flap Gear AUX4 AUX3 AUX2 AUX1 Motor Flap AUX5 AUX4 AUX3 AUX2 AUX1 AUX6 Flap AUX5 AUX4 AUX3 AUX2 AUX1 Throttle Flap Flap2 Gear AUX3 AUX2 AUX1 Motor Flap Flap2 AUX4 AUX3 AUX2 AUX1 AUX5 Flap Flap2 AUX4 AUX3 AUX2 AUX1 Airbrake Airbrake Airbrake Throttle Gear AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Gear AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 Camber Camber Camber Camber Camber Camber Camber Camber Camber AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 2AIL+4FLAP RX CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 Airplane Glider EP 4AIL+2FLAP Airplane Glider EP 4AIL+4FLAP Airplane Glider EP Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Throttle Flap Flap2 Flap3 Flap4 Gear AUX1 Motor Flap Flap2 Flap3 Flap4 AUX2 AUX1 AUX7 Flap Throttle Motor AUX3 Throttle Motor AUX1 Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Flap2 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Flap3 Flap4 AUX2 AUX1 Flap1 Flap2 Gear AUX1 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 Flap3 Flap4 Flap1 Flap2 Flap3 Flap4 Flap1 Flap2 Flap3 Flap4 Camber Camber Camber Camber Camber Camber Camber Camber Camber AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 <Model Basic Setting Procedure> 45 2AIL RX CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 Airplane Glider EP 2AIL+1FLAP Airplane Glider EP 2AIL+2FLAP Airplane Glider EP Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Throttle Motor AUX1 Throttle Motor AUX7 Throttle Motor AUX6 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Gear AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX7 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX7 AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Flap Gear AUX5 AUX4 AUX3 AUX2 AUX1 Flap AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Flap AUX6 AUX5 AUX4 AUX3 AUX2 AUX1 Gear Flap Flap2 AUX4 AUX3 AUX2 AUX1 AUX5 Flap Flap2 AUX4 AUX3 AUX2 AUX1 AUX5 Flap Flap2 AUX4 AUX3 AUX2 AUX1 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator AUX1 Camber Camber Camber Camber Camber Camber AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 2AIL+4FLAP RX CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 Airplane Glider EP 4AIL+2FLAP Airplane Glider EP 4AIL+4FLAP Airplane Glider EP Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Throttle Motor AUX4 Throttle Motor AUX4 Throttle Motor AUX2 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Gear Flap Flap2 Flap3 Flap4 AUX2 AUX1 AUX3 Flap Flap2 Flap3 Flap4 AUX2 AUX1 AUX3 Flap Flap3 Flap4 AUX2 AUX1 Gear AUX3 AUX3 Gear AUX1 AUX1 Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 AUX2 AUX1 Flap1 Flap2 Flap3 Flap4 Flap1 Flap2 Flap3 Flap4 Flap1 Flap2 Flap3 Flap4 Flap2 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Camber Camber Camber Camber Camber Camber Camber Camber Camber AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 46 <Model Basic Setting Procedure> Helicopter CH 1 2 3 4 5 6 7 8 9 10 11 12 VC1 VC2 VC3 VC4 H-4 Swash Throttle Rudder Aileron Elevator 1 Pitch Elevator 2 Gyro Governor 1 Governor 2 Needle AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 All Other Throttle Rudder Gyro Aileron Elevator Pitch Governor 1 Governor 2 Needle AUX3 AUX2 AUX1 AUX1 AUX1 AUX1 AUX1 <Model Basic Setting Procedure> 47 FUNCTIONS OF LINKAGE MENU The Linkage Menu is made up of functions which perform model addition, model type selection, frequency setting, end point setting, and other model basic settings. The functions which can be selected depend on the model type. A typical menu screen is shown below. *The display screen is an example. [Cursor Lever] [Return Key] [Data Input Dial] PUSH [Enter Button] To activate/deactivate Condition Hold: *See p. 68 for condition hold function details. *Condition hold operation is displayed. Linkage Menu functions table [SERVO MONITOR]: Displays the servo test and operation position [MODEL SELECT]: Model addition, call, deletion, copy, model name setting [MODEL TYPE]: Model type, wing type, switch type, etc. selection [FREQUENCY]: Frequency selection, modulation mode selection, receiver ID setting [FUNCTION]: Channel assignment of each function can be changed [SUB-TRIM]: Adjusts the neutral position of each servo [SERVO-REVERSE]: Servo direction reversal [FAIL SAFE]: Fail safe function and battery fail safe function setting [END POINT(ATV)]: Servo basic rudder adjustment and limit setting [THROTTLE CUT]: Stops the engine safely and easily (airplane and helicopter only) [IDLE DOWN]: Lowers the idle speed of the engine (airplane and helicopter only) [SWASH]: Swash AFR and linkage correction function (helicopter only) [TIMER]: Timer setting and lap time display [DIAL MONITOR]: Dial, sliding lever, and digital trim position display [DATA RESET]: Model memory set data reset (by item) [COND. HOLD]: Condition hold function 48 <Functions of Linkage Menu> SERVO MONITOR This is used for testing servo movement. "Moving Test" (repetition mode) and "Neutral position of a servo horn. [Cursor Lever] [Return Key] [Data Input Dial] PUSH [Enter Button] *The display screen is an example. [. . . ] Switch selection (Switch selection screen example) Edit key [Cursor Lever] [Data Input Dial] PUSH [Enter Button] When switch was selected When switch was selected, ON/OFF position setting is also performed. 1. Use the cursor lever to move the cursor (reverse-video) to the switch you want to select and push the enter button. The switch is selected and the ON/OFF position setup screen shown below is displayed. When stick, trim lever, or knob selected When a stick, trim lever, or knob is used as a switch, four operation modes can be selected by the following mode and type combination: Mode: [LINEAR](Linear)/[SYMMET](symmetrical) 1. Use the cursor lever to move the cursor (reverse-video) to the stick, trim lever, or knob you want to select and push the enter button. [. . . ]