User manual GAGGENAU AI281120

[. . . ] Gaggenau Operating and installation instruction Extractor hood AI 280120 AI 281120 Fig. 1 ELECTRIC 2 Table of Contents Operating Instructions Installation Instructions Operating modes Exhaust-air mode Circulating-air mode Coanda effect Operating for the First Time If you encounter a problem Safety instructions Operating procedure Intensive setting Special functions Filters and maintenance Grease filters Saturation indicator F Activated carbon filter Cleaning and care Replacing the light bulbsn 4 4 4 5 6 6 7 8 9 9 10 10 10 11 12 13 Important information Prior to installation Exhaust-air mode Circulating-air mode Preparing the wall Electrical connection Installation 15 16 16 17 18 19 20 3 Operating modes Exhaust-air mode Circulating-air mode · Installation accessories for exhaust air mode. Ventilation duct AD280/281-016 for ceiling heights of 2. 27­2. 44 m AD280/281-026 for ceiling heights of 2. 44­2. 76 m AD280/281-036 for ceiling heights of 2. 76­2. 98 m. · Installation accessories for circulating air mode. Ventilation duct AD280/281-126 for ceiling heights of 2. 44­2. 76 m AD280/281-136 for ceiling heights of 2. 76­2. 98 m. . · · · · · · · An activated carbon filter must be fitted for this operating mode (see Filters and maintenance). [. . . ] The grease filters can of course be cleaned at any time, even if the grease filter saturation display has not started to flash. 2 3 4 Clean the filters. Insert the clean filters back into the hood. ­ Press the button F. Cleaning the metal grease filters: · · · In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned 1 x a month. The filters can be cleaned in a dishwasher. It is however possible that they will become slightly discoloured. The filter must be placed loosely, and NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. · When cleaning the filters by hand, soak them in hot soapy water first of all. Do not use aggressive, acidic or caustic cleaners. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. 10 Activated carbon filter For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Installation and removal: IMPORTANT: The lighting must be switched OFF and cool. . 1 2 Remove the metal-mesh filters (see "Removing and inserting the metal-mesh grease filters"). Even after a while, there is still a risk of being burnt. 2 3 4 Remove the metal-mesh filters (see "Removing and inserting the metal-mesh grease filters"). Loosen the screws for the mounting rails. . Carefully remove the glass panes. 5 Remove the sockets for the fluorescent light bulbs. 6 Replace the fluorescent light bulbs with new ones available commercially (36 W, 840 Cool White, socket 2 G 11). Risk of breakage! 13 7 8 9 Insert the sockets for the fluorescent light bulbs. Tighten the screws for the mounting rails. 10 Insert the metal grease filters (see "Removing and inserting the metal grease filters"). 11 Restore the power by inserting the mains plug or switching on the fuse. Note: If the light does not function, check that the bulbs have been inserted correctly. 14 $ Important information Additional information concerning gas cookers: When installing gas hotplates, comply with the relevant national statutory regulations (e. g. in Germany: Technische Regeln Gasinstallation TRGI). [. . . ] Before installation check the enclosed wall plugs and screws are suitable for your ceiling. If necessary use special wall plugs. 200 346 Installation of the extractor hood: 1 2 3 Using the drilling template mark the position of the screws on the ceiling. Drill 4 holes Ø 8 mm for the wall plugs. Both screws are placed in a position, in which at a later stage of the installation the key-holes of the supporting frame are found (namely back left and front right from the control panel of the hood). [. . . ]