User manual GAGGENAU VG232232CA

[. . . ] Operating and assembly instructions VG 232 CA Gas cooker VG 232 CA FOR YOUR SAFETY Page 2 Warnings Page 3 Preface Page 4 1. Important notes Page 5-6 1. 1 For your safety Page 5 1. 2 Operating for the first time Page 5 1. 3 About use Page 6 2. Structure and operating principle Page 7-8 2. 1 Structure Page 7 2. 2 Special accessories Page 7 2. 3 Operating principle Page 8 3. Maintenance Page 11 5. 1 General Page 11 5. 2 Remedying slight malfunctions yourself Page 11 6. [. . . ] When using larger pots, pay attention to keeping to a minimum distance of 50 mm (2") between the cooking vessel and combustible surroundings. A minimum distance of 15 mm (19/32") must be observed between the control knob and the pot or pan. In the event of malfunctions, contact your specialist dealer or your responsible Gaggenau after-sales service. Tip: When buying pots, pay attention to the fact that the manufacturer frequently specifies the top pot diameter, which is generally larger than the diameter of the base. Observe the manufacturer's specification!Use cooking utensils that the manufacturer states as being "suitable for gas". Preferably use the larger cooking zone for brief cooking, deep fat frying and brief frying of large quantities. Preferably use the smaller ring for soaking, warming up and keeping warm, even when large quantities are involved. 6 2. Structure and operating principle 2. 1 Structure 1 High-power burner B 9500 BTU (2. 8 kW) 1 2 3 4 5 Fig. 2 2 Normal burner A 6500 BTU (1. 9 kW) 3 Pot support 4 Control knob for the front cooking position 5 Control knob for the rear cooking position 6 Burner cover 6 7 Burner head 8 Spark plug for automatic ignition 9 Thermal sensor for flame monitor 7 8 Fig. 3 9 2. 2 Special accessories You can order the following special accessories: ­ VV 200-000: Connecting strip ­ VD 201-010: Appliance cover (If an appliance cover is fitted, the pot support must be removed when closing. ) 7 2. 3 Operating principle The appliance features one-hand operation. That is to say, the ignition is activated when the control knob is pressed briefly. After igniting, keep the control knob pressed for around 5-8 seconds more because the heat sensor that opens the gas channel has to warm up first. The gas hob has 1 normal burner (front burner) and 1 high-intensity burner (rear burner). All burners have a thermal protection device that prevents unburned gas from escaping in the open position. Off The total rated thermal load amounts to: 16000 BTU (4. 7 kW) referred to Hs* (gross calorific value) 14300 BTU (4. 2 kW) referred to Hi (calorific value) The specified rated load is defined by installation of the fixed nozzles. ­ Whenever required, clean the burner head with a moist cloth. ­ Soak burnt-in remainders in a little water and detergent. This loosens even the most stubborn of soiling. Do not use any abrasive agents and abrasive sponges. ­ As the result of heat development, slight discoloration can appear on the stainless steel surface. Do not attempt to scrape away such discoloration. Distribute stainless steel care agents uniformly and thinly on the hob (not on the control panel!). [. . . ] 10 See table on Page 12 for details of nozzle settings. 16 Replacing the main nozzle 2 Proceed as follows: ­ The main nozzle 2 is visible after detaching the burner cover (see Fig. It is unscrewed with a special screw key. ­ Unscrew the nozzle and insert the new nozzle as specified in the main nozzle table. The nozzle must be screwed in fully and firmly (torque 1. 5 Nm) (metallic seal). [. . . ]