User manual GALLIEN-KRUEGER 200MV

[. . . ] (2) -10dB Pad This switch provides 10dB attenuation of the input signal if the signal is too "hot"(ie, active electronics etc. ). A signal that is too "hot" will cause distortion in the unit even at low volumes. Level Control This provides control of the signal coming in the balanced input jack. It controls the level going to the internal amplifier as well as the level going out the 'line out' jack (#16) and also the level going out the balanced output jack (#17)(when switch #18 is in). [. . . ] (12) Master Volume Control This is the main control for what goes to the internal amplifier (as well as to the headphones)from CH. (12) Headphone Jack This jack accepts a 1/4'' stereo phone plug (do not use a plug that is not stereo) for the use of stereo headphones. The signal sent out of this jack is the same as that being delivered to the speakers but at a lower level. (13) Auxiliary In 1&2 These jacks accept 1/4'' phone plugs and can be driven by sources such as a 'PA' mixing board (monitor send), a drum machine, an electric guitar (with effects or an active preamp), another GK 200MV, a stereo cassette deck, etc. The two inputs are summed internally and are controlled by the front panel controls (#9, 10, 11). (14) Auxiliary Out Jack This jack puts out the sum of AUX. In 1&2 (#14) at unity gain (same level). It is not affected by any of the front panel controls. If you have a monitor send from a 'PA' board going into the AUX. In (#14), you can use this jack to 'daisy chain' to other 200MVs or monitoring devices so everyone in the 'chain' gets the same signal. (15) Line Out Jack The line out jack sends out the signals from CH. 1&2 (#1, 4) post level controls, EQ and Echo. This signal is the same as what is heard in the internal amplifier minus the AUX. This can be used for overdubbing in a home recording situation to record just the voice or instrument from CH. 1&2 (#1, 4) while listening to prerecorded music from the AUX. (17, 18) Balanced Output/Switch Combination This is a dual purpose output jack. With the switch in the 'out' position the output is just a balanced output of what is going in the CH> 2 (#4) input times a gain of 5. When the switch is pushed in, the output becomes a balanced version of exactly what is on line out. 2, which are controlled by their respective level controls, with EQ and Echo. This control allows special equalization and Echo to be added to the vocals or instruments before they are sent to the main mixing board. (19) Channel 1 Direct This jack provides the same signal that is being fed into the CH. It is not affected by the level control (#3), however, it is affected by the -10dB pad (#2). [. . . ] If you should need service, please call us or your local GK dealer to find out where the nearest certified GK repair station is. Specifications Power @ 400Hz 100 Watts into 4 Ohms @ . 1 THD 72 Watts into 8 Ohms @ . 1% THD Signal - to - noise Ratio :>80dB Max Distortion :. 35% Frequency Response :Less than ± 1dB 20- 20K Hz Line out :+ 1. 6dBV (Nom) Direct Outs - into 1K OHM Balanced input CH. 1 & 2 Post Effects (Switch In) - 20dBV (Nom) Auxiliary Output :Equal to AUX. In 1 & 2 Levels Channel 1 Input Input Impedance - 5. 6K OHM Max input Level - 95mV RMS W/-10dB Switch in - 300mV Input Sensitivity - 2. 4mV Channel 2 Input Input Impedance - 1M OHM Max input level - 2. 4V RMS Input Sensitivity - 30mV Auxiliary Input Input Impedance - 1M OHM Max input Level - . 9V RMS Input Sensitivity - 8mV Sample Setups OPTIONAL : YOU CAN ADD THE 7-BAND GRAPHIC AND ECHO TO THE MON. [. . . ]