User manual GARMIN G1000 MOONEY VHFNAV COM PILOTS GUIDE M20M M20R

[. . . ] G1000 TM VHF NAV/COM pilot's guide for Mooney M20M & M20R Record of Revisions Revision Date of Revision Revision Page Range A 5/5/05 4-1 ­ 4-21 Description Initial release. Garmin G1000 VHF NAV/COM Pilot's Guide for Mooney M20M & M20R 190-00445-01 Rev. A INTRODUCTION 4. 1 VHF NAV/COM OVERVIEW The G1000 VHF NAV/COM frequency controls and windows are located in the top corners of the Primary Flight Display (PFD) and Multi Function Display (MFD). The NAV controls, windows and fields are located on the left side. The COM controls, windows and fields are on the right, as shown in the figure below. NAV Controls NAV Frequency Window The G1000 VHF NAV/COM interface includes: · · · · · · Windows and fields Radio selection Tuning box Frequency Transfer Arrow Radio status indications Controls COM Frequency Window COM Controls Figure 4. 1. 1 G1000 VHF NAV/COM Interface (PFD) 190-00445-01 Rev. [. . . ] When the Morse code identifier is OFF, the ID indication disappears and the Morse code is filtered out of the NAV audio. The Morse code identifier is ON for the GHM VOR. Figure 4. 3. 2 ID Indication VOLUME NAV radio volume level can be adjusted from 0 to 100% in increments of 3. 25%, using the VOL/PUSH ID knob. Turning the VOL/PUSH ID knob clockwise increases volume, turning the knob counterclockwise decreases volume. When adjusting the volume for a NAV radio, volume level is displayed in place of the standby NAV frequency. Volume level remains in the NAV Frequency window for two seconds after the change. The Morse code ID for an active NAV channel is heard when the white ID is displayed and the NAV radio is selected on the audio panel. Nav audio is available with the ID filtered out for listening to HIWAS and FSS transmissions on VOR stations. NAV2 is the NAV radio selected on the audio panel. The Morse code identifier for the GHM VOR can be heard. NAV section of the audio panel Figure 4. 3. 1 NAV Volume Level Figure 4. 3. 3 Morse Code Identifier Audio NOTE: When a VOR signal is received, the VOR/ LOC Morse code identifier is displayed to the right of the active NAV frequency. 190-00445-01 Rev. The PFD allows auto-tuning of COM frequencies associated with the nearest airports. The MFD provides auto-tuning of both COM and NAV frequencies from waypoint and nearest pages. In addition, the primary NAV frequency is entered automatically in the NAV window during yapproach loading or approach activation. Frequencies can be automatically loaded into the frequency windows in the following ways: · By using the ENT key when the frequency is highlighted on the appropriate page (PFD and MFD). · When loading or activating an approach (PFD and MFD). NOTE: Turn the FMS knob to scroll through a list of frequencies. Press the ENT key to load a highlighted frequency into the frequency window. AUTO-TUNING ON THE PFD COM frequencies for the nearest airports may be viewed and automatically loaded from the Nearest Airports window on the PFD. To auto-tune a COM frequency for a nearby airport: 1. Press the NRST softkey to open the Nearest Airports window, which displays the list of airport identifiers and COM frequencies. Turn either FMS knob to highlight the desired COM frequency. Press the ENT key to load the COM frequency into the COM tuning box. NOTE: When the desired frequency is entered in the tuning box, it becomes a standby frequency. Pressing Frequency Transfer places this frequency into the active field. 2. 3. Turn the FMS knob to scroll through a list of frequencies. Pressing the NRST softkey opens the Nearest Airports window Figure 4. 4. 2 Nearest Airports Window (PFD) Figure 4. 4. 1 Loading Frequencies 190-00445-01 Rev. A Garmin G1000 VHF NAV/COM Pilot's Guide for Mooney M20M & M20R 4-13 OPERATION ­ AUTO-TUNING AUTO-TUNING ON THE MFD Frequencies can be selected and loaded from the following MFD pages: · WPT ­ Airport Information · WPT ­ VOR Information · NRST ­ Nearest Airports · NRST ­ Nearest VOR · NRST ­ Nearest Frequencies WPT ­ Information Page The Airport Information Page displays runway information and a list of frequencies for the selected airport identifier as well as departure, arrival and approach information. To display the entire list of frequencies for an airport: 1. On the Airport Information Page, press the INFO softkey to display runway and frequency information for a specific airport. [. . . ] Press the ENT key to load the desired FSS frequency into the COM or NAV tuning box. NOTE: The Nearest FSS window contains a list of FSS names as well as bearing and distance information from the transmitting antenna. Figure 4. 4. 9 NRST ­ Nearest Frequencies Page 3. 190-00445-01 Rev. A Garmin G1000 VHF NAV/COM Pilot's Guide for Mooney M20M & M20R 4-19 OPERATION ­ AUTO-TUNING AUTO-TUNING ON APPROACH ACTIVATION (NAV FREQUENCIES) NAV frequencies are automatically loaded into the NAV Frequency window on approach activation, regardless of the display unit being used. NOTE: The primary NAV frequency becomes auto-tuned upon loading an approach. To auto-tune a NAV frequency if the desired approach is not already loaded: 1. Press the PROC key to open the Procedures window. Turn the large FMS knob to highlight the `SELECT APPROACH' menu option and press the ENT key. [. . . ]