User manual GARMIN G1000 NON-AIRFRAMESPECIFIC TRAINER USER SGUIDE

[. . . ] G1000 TM trainer user's guide Garmin G1000 Trainer User's Guide 190-00419-01 Rev. C COPYRIGHT © 2004, 2005 Garmin Ltd. Garmin International, Inc. , 1200 East 151st Street, Olathe, Kansas 66062, U. S. A. Tel: 913/397. 8200 Fax: 913/397. 8282 Garmin AT, Inc. , 2345 Turner Road SE, Salem, Oregon 97302, U. S. A. [. . . ] The contractor/manufacturer is Garmin International, Inc. , 1200 East 151st Street, Olathe, KS 66062, U. S. A. EXPORT CONTROLS: You agree not to export or re-export the Product to any country in violation of the export control laws of the United States of America. GARMIN LICENSORS: With respect to Third Party Software contained in the Product, the provisions of this License shall inure to the benefit of the licensors to Garmin of third party software contained in the Product. Such licensors shall be third party beneficiaries hereof, and shall have the right to enforce any and all rights and claims arising hereunder with respect to such third party software, including the right to bring an action directly against you, in the event of a breach by you of your obligations hereunder. GENERAL: This License is the entire agreement between us, superseding any other agreement or discussions, oral or written, and may not be changed except by a signed agreement. This License shall be governed by and construed in accordance with the laws of the State of Kansas, United States of America. If any provision of this License is declared by a court of competent jurisdiction to be invalid, illegal, or unenforceable, such a provision shall be severed from the License and the other provisions shall remain in full force and effect. iv Garmin G1000 Trainer User's Guide 190-00419-01 Rev. C MINIMUM SYSTEM REQUIREMENTS Thank you for using the Garmin G1000 Trainer. The G1000 Trainer is designed to simulate the behavior of the G1000 system interface and provides the user with a safe environment in which to learn the basic operation of the system. This manual is designed both to guide the user through the G1000 Trainer software application installation and to provide information as to the operation of the G1000 Trainer interface. More detailed information is presented in the Help feature of the G1000 Trainer software. MINIMUM PC SYSTEM REQUIREMENTS · · · · · · · 1. 8 GHz processor 256 MB RAM Windows® 2000 or XP 200 MB free hard disk space CD-ROM drive Microsoft® DirectX® 9. 0b (software application included on the G1000 Trainer CD-ROM) Video Card: DirectX capable card with a minimum of 64 MB of memory and video card drivers that support DirectX 9. 0b. NOTE: Intel integrated graphics controllers are NOT supported. · Screen resolution: 1280 pixels wide x 1024 pixels high · Four-axis joystick with throttle/power and rudder control (optional). CAUTION: The G1000 Trainer software application is not designed to run with processor hyperthreading enabled. For processors that support hyperthreading, hyperthreading must be disabled in the BIOS before starting the G1000 Trainer software application. 190-00419-01 Rev. C Garmin G1000 Trainer User's Guide 1 INSTALLATION INSTALLING THE G1000 TRAINER To install the G1000 Trainer software application: 1. Insert the G1000 Trainer CD-ROM into the CD-ROM drive of the computer (PC) on which the G1000 Trainer software application is to be installed. 2a. The softkeys are located across the bottom of the display and are designed to perform various functions depending upon the control display mode and the specific page being displayed. Power Button Although the G1000 System does not feature a power button, such a button has been added to the top left corner of the G1000 Trainer bezel for practical purposes. NOTE: Pressing the power button while the G1000 system is running stops the system. G1000 Control Display Right-click Menu The right-click menu can be displayed at any time by right-clicking anywhere on the G1000 control display. As illustrated below, this menu includes the following options: Reversionary Mode, PFD Mode, MFD Mode, Online LRUs, Pause. Figure 4 Right-click Menu Airframe Selection The G1000 Trainer is designed to simulate specific airframes. Ensure that the G1000 Trainer is powered off. Click the `Airframe' menu and select the desired airframe. NOTE: At initial G1000 Trainer power-up, the airframe listed first in the `Airframe' menu is selected by default. Display Mode The G1000 control display can be configured at any time as either a Primary Flight Display (PFD) or a Multi Function Display (MFD). The G1000 control display can also be set at any time to Reversionary mode (or backup mode), a mode in which all important flight information from both the PFD and the MFD is presented. To configure the G1000 Trainer as a PFD or an MFD: 1. Click the `Options' menu and select the `PFD Mode' or `MFD Mode' menu option, respectively. [. . . ] In Demo mode, control inputs cannot be simulated in real time. However, a number of flight parameters can be configured in the Demo Mode window in order to allow flight simulation. The available configurable flight parameters are as follows (see figure below): · TRK MODE ­ Track mode may be set to either `TRK FPL' or `MANUAL'. In TRK FPL (track flight plan) mode, HEADING is set automatically. [. . . ]