User manual GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL INSTALLATION INSTRUCTIONS

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL. We hope that this GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL user guide will be useful to you.

Lastmanuals help download the user guide GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL.


Mode d'emploi GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL
Download

You may also download the following manuals related to this product:

   GARMIN GMR 606 xHD OPEN ARRAY AND PEDESTAL INSTALLATION (1587 ko)

Manual abstract: user guide GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTALINSTALLATION INSTRUCTIONS

Detailed instructions for use are in the User's Guide.

[. . . ] GMRTM 600/1200 Series Radar Installation Instructions Properly install your GMR 600/1200 series radar according to the following instructions. If you experience difficulty installing the chartplotter, seek the assistance of a professional installer, or contact Garmin® Product Support. Before installing your GMR 600/1200 series radar, confirm that the package contains the items listed on the box. If any parts are missing, contact your Garmin dealer immediately. WarnInG: Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. [. . . ] From the Radar page, press the Setup softkey to open the setup page. From the Setup page, using the ROCKER, select the Advanced tab. Highlight the Front of Boat Offset slider, and press ENTER. The preview window changes as you adjust the slider. After an offset is determined, press ENTER to save, and press QUIT to return to the Radar page. bow Front of boat Offset = 180° GMR 600/100 Series Installation Instructions stern 7 Front of Boat Offset = 0° Installing the Field-Installable RJ-45 Network Connector (Optional) O-Ring RJ-45 modular plug Ethernet cable termination opper tape strip (not shown) C Preparing the Network Cable A field-installable RJ-45 network connector is provided for you to create a network cable that is the correct length for your installation. 1. Cleanly cut your Ethernet cable to the desired length. Retain the cut RJ-45 connector for Step 4. Remove the strain-relief nut from the cable-connection housing and slide it onto the cut end of the cable as shown. Feed the cut cable end through the connection housing as shown. Cut end of cable Strain relief Connection housing 4. Examine the RJ-45 connector removed in Step 1 and compare it to the wire positions in the table below. Note which cable side, A or B, was removed in Step 1. Position 1 2 3 4 5 6 7 8 Wire Color--Main/Stripe Side A White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown Side B White/Green Green White/Orange Blue White/Blue Orange White/Brown Brown Position 8 Position 1 nOTe: The Garmin Marine Network requires cross-over cables not exceeding 100 meters between devices. When constructing a custom cable from bulk wire, you must create both a Side A and Side B. 5. Prepare the cable for plug installation: · Using a sharp knife, insert the blade between the cable shield and jacket. Slit the jacket 5/8" back from the trimmed end of the cable. (1 mm) · Peel the jacket back and remove the slit portion. · TrimtheshieldandMylarfilmawayfromwires. Becarefulnottocutanyofthewires. · Fold the drain wire back over the jacket and trim to approximately 9/16 in. · Untwist the wire pairs enough to ensure a proper connection. Drain · Arrangeindividualwiresinproperorderaccordingtothetableshownabove. Forexample, ifyouhaveidentified wire the end of the cable in Step 4 as Side A, arrange the wires for Side A. If you are constructing a custom cable from bulk wire, you need to make both a Side A and a Side B connection. · Trim the wire ends to an even length, leaving approximately 9/16 in. (14 mm) from the ends to the jacket edge. [. . . ] This warranty is provided by the local in-country distributor and this distributor provides local service for your unit. Distributor warranties are only valid in the area of intended distribution. Units purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service. 1200 East 151st Street, Olathe, Kansas 66062, USA Tel. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual GARMIN GMR 606 XHD OPEN ARRAY AND PEDESTAL will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag