User manual GARMIN GPSMAP 3006C/3010C INSTALLATION INSTRUCTIONS REV. A, SEP, 2008

[. . . ] GPSMAP® 3000 Series Installation Instructions The GPSMAP 3000 series chartplotter and GPS antenna must be properly installed according to the following instructions. You need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. [. . . ] Placethesealpadonthebottomofthesurface-mountbracket. Makesurethatthescrew holesalign. UsetheincludedM4screwstoattachthesurface-mountbrackettothemounting surface. RoutetheGPS17xcablethroughthe1in. cableholeandconnectittothe GPS17x. MakesurethelargegasketisinplaceonthebottomoftheGPS17xantenna, place theantennaonthesurface-mountbracket, andtwistitclockwisetolockitin Surface-mount place. SecuretheantennatothemountingbracketwiththeincludedM3setscrew. RoutetheGPS17xcableawayfromsourcesofelectronicinterference, and Mounting surface connectittopowerandtoyourGPSMAP3000serieschartplotter(Page6). GPS 17x antenna Rubber gasket Pole Mounting the GPS 17x Antenna With the pole-mount adapter attached to the GPS 17x, you can install the GPS 17x on a standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch--not included). You can run the GPS 17x cable through the pole or outside the pole. To mount the GPS 17x with the cable run outside the pole: 1. RoutetheGPS17xdropcablethroughthepole-mountadapter, andplacethecableintheverticalslotalongthebaseofthepole-mount adapter. Threadthepole-mountadapterontoastandard1in. ODpipe-threaded-polemarinemount (14threadsperinch--notincluded). Donotovertightentheadapter. ConnecttheGPS17xcabletotheGPS17xantenna. PlacetheGPS17xantennaonthepole-mountadapterandtwistitclockwisetolockitinplace. SecuretheantennatotheadapterwiththeincludedM3setscrew. (Optional)WiththeGPS17xinstalledonthepolemount, filltheremaininggapintheverticalcable slotwithamarinesealant. Attachthemarinemounttotheboatifitisnotalreadyattached. RoutetheGPS17xcableawayfromsourcesofelectronicinterference, andconnectittopower Pole-mount andtoyourGPSMAP3000serieschartplotter(Page6). adapter To mount the GPS 17x with the cable run through the pole: Vertical cable slot 1. Positionastandard1in. ODpipe-threaded-polemarinemount(14threadsperinch--notincluded) inthepreferredlocation, andmarktheapproximatecenterofthepole. Drillaholeusinga3/4in. (19mm)drillbitforthecabletopassthrough. Fastenthemarinemounttotheboat. GPSMAP 3000 Series Installation Instructions 4. Threadthepole-mountadapterontothepole. Donotovertightentheadapter. RoutetheGPS17xcablethroughthepoleandconnectittotheGPS17xantenna. [. . . ] All components of the Garmin Marine Network must be connected to power, because they do not receive power through the network connections. GPS 17x Garmin GPSMAP 3000 Series Chartplotter Garmin GPSMAP 3000 Series Chartplotter Simple Garmin Marine Network With Two Chartplotters If more than two GPSMAP 3000 series chartplotter are installed, use a Garmin Marine Network Port Expander (GMS 10) to expand the network. If two or more GPSMAP 3000 series chartplotters are installed and networked, only one GPS 17x antenna needs to be installed. You can add up to five total devices to the Network Port Expander. If more than five are needed, you can add more Network Port Expanders to the network. [. . . ]