User manual GAS GAS PAMPERA 125 2007

[. . . ] PAMPERA 125-07 INTRODUCTION GAS GAS would like to thank you for your confidence. By choosing a new PAMPERA 125 2007 you have become part of the great GAS GAS family and, as a user of the number one manufacturer of off-road motorbikes, you deserve the best treatment we can offer you both in our after-sales relations and in the information given in this manual. The new PAMPERA 125 2007 is a motorcycle that has been designed for your leisure. In fact, it is the result of many years of competition and experience in this highly demanding discipline and of the many excellent results obtained by the great riders who have provided the fundamental data to enable us to create excellent GAS GAS motorcycles with several key advantages: reliability, high-performance and stability. [. . . ] - Rotate the bolt A until the engine runs continuously. Note - Rotating the screw A clockwise will increase the engine speed. - Rotating the screw A anticlockwise will decrease the engine speed. - Rotate the bolt B until the engine reaches the highest speed. Note - Tightening the screw B will restrict the flow of air-fuel mixture - Loosening the screw B will open the flow of air-fuel mixture - Tighten the screw B about 1/4 of a turn. Rotate the bolt A until the engine reaches the required idle speed. A B MAINTENANCE INSTRUCTIONS 33 SPARK PLUG Note - The spark plug should be regularly checked, according to the "Maintenance table" or if the engine has a problem. See the section "Trouble shooting". - Note that if the engine performance falls then this could be due to the spark plug. Standard spark plug Electrode spacing TORCH D8RTC 0. 7 to 0. 8 mm (0. 028 ­ 0. 031 in) A B WARNING Incorrect installation of the spark plug or the choice of an incorrect temperature grade may cause serious damage to the engine. This damage is not covered by the guarantee. Always use spark plugs recommended by GAS GAS. Consult the dealers or a qualified mechanic to know which spark plug is best for your bike. Spark plug - removing To remove the spark plug, take the following steps: - Remove the cap A from the spark plug. - Remove the spark plug B from its allotment using the special spark plug wrench. Note Check the colour and the appearance of deposits on the spark plug. These deposits indicate if the standard spark plug is the most suitable for your motorcycle or if it should be replaced by another of a different temperature grade. - If there is soot on the spark plug then clean using a metal brush. - Check and, if necessary, adjust the electrode spacing to between 0. 7 - 0. 8 mm (0. 028 - 0. 031 in). WARNING If the spark plug electrodes are oxidised, damaged or the insulation is broken then replace the plug. 34 MAINTENANCE INSTRUCTIONS - Fit the spark plug and tighten to the specified torque of 11 Nm (1. 0 kgm). See also the "Tightening torques table". - Refit the hood for the spark plug. B Note To ensure correct operation of the spark plug, keep the protection hood clean and dry. A AIR FILTER A clean air filter will provide good engine performance and prolong its useful life. An obstructed air filter restricts the air intake of the engine, increasing the petrol consumption and reducing the engine power as well as causing the destruction of the spark plug. WARNING If dirt enters the engine then this will lead to excessive wear and engine damage. Inspect the air filter regularly as indicated in the Maintenance table. [. . . ] f) The vehicle has been stored or transported in a way that does not meet the corresponding technical requirements. g) The vehicle has been used for extraordinary use such as for competitions, races or attempts at any record whatsoever. h) The vehicle has suffered a fall or accident provoking the damage indirectly or directly. Exclusions from the warranty The following items will be excluded from the warranty: a) normal wear and tear on parts including, without limitation, spark plugs, batteries, fuel filters, oil filter elements, drive chains (secondary), engine pinions, rear sprockets, air filters, brake discs, brake pads, clutch discs, lamps, fuses, carbon brushes, footrest rubbers, tires, tubes, cables and other rubber components. [. . . ]