User manual GATEWAY LN-520

[. . . ] LN-520 Digital A/V Receiver INTRODUCTION READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] · When pressing this button without selecting the tuner, the tuner will be selected automatically. P. SCAN 31 www. gateway. com OPERATIONS ANALOG AUDIO/VIDEO RECORDING · The analog signals (except front L/R channel) from the 7 CH DIRECT inputs as well as the digital signals from the coaxial or optical digital input cannot be recorded. · The volume and tone (bass, treble) settings have no effect on the recording signals. Recording with TAPE 1 Select the desired input as a recording source except for TAPE. 2 3 Start recording on the TAPE. Start play on the desired input. INPUT SELECTOR or TUNER AUX VIDEO1 VIDEO2 VIDEO3 Dubbing from video components onto VIDEO 1 2 3 Start recording on the VIDEO 1. 1 Select VIDEO 2 or VIDEO 3 as a recording source. Start play on the VIDEO 2 or the VIDEO 3. INPUT SELECTOR or VIDEO2 VIDEO3 · The audio and video signals from the VIDEO 2 or the VIDEO 3 will be dubbed onto the VIDEO 1 and you can enjoy them on the TV set and from the speakers. Dubbing the audio and video signals separately onto VIDEO 1 Example) When dubbing the VIDEO 2 video signal and the CD audio signal separately onto VIDEO 1. 2 Press the OSD button on the remote control unit and select FUNCTION SELECT VIDEO SELECT VIDEO 2. (Refer to page 36. ) 1 Select AUX as an audio recording source. CD player should be connected to AUX jacks. OSD INPUT SELECTOR AUX or www. gateway. com 32 OPERATIONS 3 Start recording on the VIDEO 1. 4 Start play on the AUX and the VIDEO 2 respectively. · The audio signal from the AUX and the video signal from the VIDEO 2 will be dubbed and you can enjoy them on the TV set and from the speakers. If you select AUX for hearing and VIDEO 1 for seeing, whenever you select AUX, the VIDEO 1 is selected automatically as video input source. So you are sure to be observe the order and doing of the above steps 1 and 2. DIGITAL AUDIO RECORDING WITH MD RECORDER · Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to "CONNECTING AUDIO COMPONENTS"/ " CONNECTING VEDIO COMPONENTS"/"CONNECTING DIGITAL INs and OUT" on page 5~6 and the operating instructions of the MD recorder or CD recorder. Notes: · Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc. · In most DVDs as well as some CDs, etc. , digital recording may not be available depending on the signal format. · There are some restrictions on recording digital signals. When making digital recordings, refer to the operating instructions of your digital recording equipment to know what restrictions are imposed. 1 Select a desired input of AUX, VIDEO 1~3 as a recording source. 2 For digital recording, select the desired digital input as recording signal input. DIGITAL INPUT AM/FM MODE INPUT SELECTOR or AUX VIDEO1 VIDEO2 VIDEO3 · Each time this button is pressed, the corresponding input is selected as follows: A(nalog) o(ptical) 1 o(ptical) 2 c(oaxial) 1 Note : When the selected digital input is not connected, "DIGITAL" indicator flickers. There will be no recording as well as no sound. 3 33 Start recording on the component connected to OPTICAL DIGITAL OUT. 4 Start play on the desired input. www. gateway. com OPERATIONS OTHER FUNCTIONS Operating the sleep timer · The sleep timer allows this unit to continue to operate for a specified period of time before automatically shutting off. · To set the receiver to automatically turn off after the specified period of time. Adjusting the brightness of the fluorescent displays DIMMER SLEEP · Each time this button is pressed, the brightness of fluorescent display of this unit changes as follows; ON dimmer OFF · Each time this button is pressed, the sleep time changes and "GOOD NIGHT" message scrolls. 10 20 30 60 90 OFF Unit : minutes · In the display OFF mode, pressing any button will restore the display ON mode. · While operating the sleep timer, "SLEEP" lights up. www. gateway. com 34 USING THE OSD This unit incorporates an OSD(On-screen display) function to provide information about basic operation of this unit and to simplify the setup procedures. The OSD function uses a monitor TV connected to this unit as a display and has two kinds of display modes such as current status display and menu screen. Notes: · Any on-screen display shown on the monitor TV will not be recorded onto VIDEO 1. · In some countries, this unit allows you to select either NTSC or PAL color system as video format. If it is different from your video components and video softwares, etc. , in the standby mode, press the ADJUST down( ) button keeping the SETUP button pressed on the front panel, then the video format is changed to the NTSC or the PAL color system. However, it is fixed to NTSC color system in other countries. CURRENT STATUS DISPLAY When the AUTO OSD mode is set to ON on the menu screen, this mode shows the status corresponding to each operation. · The on-screen display will automatically disappear in several seconds. · For examples, there are 2 status displays as follows. When selecting the desired input source When selecting the TEST TONE mode Input source Digital input · When the speaker setting is "N", the test tone of the corresponding channel is not shown. · When adjusting each channel level or overall volume, the volume level display will be shown. [. . . ] If there is any inconsistency between this Agreement and any other agreement included with or relating to products or services purchased from Gateway, this Agreement shall govern. This Agreement may not be modified, altered or amended without the written agreement of Gateway. Any additional or altered terms attached to your order shall be null and void, unless expressly agreed to in writing by Gateway. If any term of this Agreement is illegal or unenforceable, the legality and enforceability of the remaining provisions shall not be affected or impaired. [. . . ]