User manual GE SECURITY CONCORD

[. . . ] i CO N CO RD STAY AWAY 1 5 2 6 3 7 U s e r 's G u i d e 4 8 Bypass Trouble ALARM Both Flashing Check Status Enter Code Power NO DELAY Test System Weekly Off Stay Away Test System Weekly Off Stay Away A press both 1 No Delay 2 Silent 3 Pager A press both 1 No Delay 2 Silent 3 Pager B press both 4 Features 5 System 6 Menu B press both 4 Features 5 System 6 Menu C press both 7 Status 8 Lights 9 Bypass C press both 7 Status 8 Lights 9 Bypass D * 0 # D * 0 # ii Commands at a Glance Disarm the system. Arm system with No Delay. 1 + CODE 2 + CODE 3 + CODE Press and hold both POLICE buttons for 2 seconds. Press and hold both AUXILIARY buttons for 2 seconds. Press and hold both FIRE buttons for 2 seconds. 2 + CODE + 4 or 3 + CODE + 4 2 + CODE + 6 or 3 + CODE + 6 Indirectly: Arm system for Latchkey. Bypass a sensor. 2 + CODE + or 3 + CODE + + CODE + Sensor Number or Directly: Arm system silently. 5 + 2 + CODE 5 + 3 + CODE Arm system with exit lights off. [. . . ] If you need assistance setting up a time schedule that fits your needs, see Section 10. Scheduling Latchkey Opening and/or Closing: 2. 3. L a tc h k e y d is a r m o c c u r s w it h in t im e s c h e d u le . 1. At an alphanumeric touchpad, enter User Programming by pressing 9 + System or Partition Master CODE. 2. L a tc h k e y p a g e s e n t. L a t c h k e y O p e n in g S c h e d u le 5 :0 0 3 :0 0 Press B until the touchpad displays "ATTACH SCHEDULES TO EVENTS, " then press . To schedule: · Latchkey Opening, press when the touchpad displays "LATCHKEY OPENING. " · Or, press B until the touchpad displays "LATCHKEY CLOSING, " then press +6 S y s te m a rm e d S y s te m 111 d is a r m e d . In Advanced Latchkey use, paging is available only during the time schedule(s) that you assign to it. Latchkey Closing 4. Latchkey Closing can be used alone, or in addition to Latchkey Opening. Assign the Latchkey If L a t c h k e y a r m in g Closing feature a o c c u r s w ith in time schedule. nated user within the assigned time, schedule sends a Closing page: L a t c h k e y C lo s in g S c h e d u le 6 :0 0 8 :0 0 222 or333 S y s te m d is a r m e d S y s te m a rm e d If you want a page to be sent every time Latchkey-designated users codes arm or disarm the system, apply the same time schedules under Latchkey Opening (Basic) and Latchkey Closing. The touchpad displays the first available time schedule. Enter 2 to assign the time schedule or 1 to make the time schedule inactive for this event. Press B to go to the next schedule and repeat steps 4 and 5. When you've finished attaching the desired time schedules, press , + 7 + to exit User Programming. 5. 6. 3. Applying the Latchkey 6 The Latchkey modifier 6 is pressed after the arming keypress sequence. Applying the Latchkey modifier: · At any touchpad, press 2 or 3 + CODE + 6. The touchpad displays, "LATCHKEY PAGER ON. " An LED touchpad or Touchtone phone can be used to set up Latchkey paging, but an alphanumeric touchpad works much better because of its extensive feedback. See Appendix C for LED and phone programming instructions. 6 must be pressed within 5 seconds of arming. 26 SECTION 15: NOTIFY BY EXCEPTION The Notify by Exception feature allows programmed pagerholders and/or the central station to be notified when arming or disarming occurs outside of specified time schedules. Here are two specific examples of how the Notify by Exception feature might be used in a business setting: · Every morning you'd like to be notified if your business is disarmed after its normal opening time. · Every evening you'd like to be notified if your business is armed before its normal closing time. Exception Closing Reports report the arming level as 222 (2--STAY) or 333 (3--AWAY), and the user code that armed to that level. See Table 1 in Section 10 for more information on paging reports. When Will this Feature Be Active? The most typical setup of this feature makes use of both Exception Opening and Exception Closing. (It is possible to use Exception Opening only or Exception Closing only, however. ) The following figures show what page message would be sent given the time the system was armed or disarmed. Page In the Event of . . You can set up the Notify by Exception feature to page in the following instances: · Send a page if the system is disarmed before the Opening time schedule begins or after the Opening time schedule has ended. (Exception Opening) · Send a page if the system is armed before the Closing time schedule begins or after the Closing time schedule has ended. (Exception Closing) Assigning a Time Schedule to Exception Opening and Closing Follow these steps to define Opening and Closing schedules for Exception paging. [. . . ] The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. "AVIS: - L étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d´exploitation et de sécurité des réseaux de télécommunications. Le ministère n´assure toutefois pas que le matériel fonctionnera a la satisfaction de l´utilisateur. [. . . ]