User manual GE SECURITY RANGER 8600E REV A

[. . . ] Press and hold both FIRE buttons for 2 seconds. 2 + CODE + 4 or 3 + CODE + 4 Bypass a sensor. Indirectly: 2 + CODE + + CODE or 3 + CODE + + CODE Directly: + CODE + Sensor Number Arm system silently. 5 + 2 + CODE or 5 + 3 + CODE Arm system with exit lights off. 2 + CODE + 0 or 3 + CODE + 0 Turn all lights on/off. Output Control Check the system status. 0+0 0 + Light number 7 + 7 + Output number , for a short status report , + , for a long status report 7+1 +7+3 7+6 Turn Chime on/off. (This is a phone command only. ) Check Alarm Memory xxxix Contents Getting to Know Your Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Changing the touchpad display affects only the touchpad currently being used. To change touchpad display brightness: 1. Enter the programming menus by pressing 9 + System or Partition Master Code. Select a brightness level: 0 + Off 1 + Low 2 + Medium 3 + High 4. Press , + 6 + to exit the programming menus. After dimming the display, pressing any button momentarily returns the display to full brightness. After 15 seconds without touchpad activity, the display returns to the set dimmed level. If an alarm occurs while the display is dimmed, it automatically returns to the full brightness level and stays that way until you disarm your system. ADJUSTING SYSTEM SOUNDS AND TOUCHPAD BRIGHTNESS Arming Your System Silently Use the Silent Arming feature to arm your system without disturbing people throughout the house with arming status beeps. There are two methods for implementing Silent Arming. Silent on Demand (User presses 5 before arming) Arming Always Silent (Silent Arming feature on) Regardless of the method employed, when Silent Arming is in effect no Exit beeps sound. Note: Protest beeps will always sound when indirectly bypassing a sensor. Adjusting the Volume If your system includes a phone and voice module, you can adjust the volume of the system sounds. and 5 a. m. , Monday through Friday (ending Saturday morning). By simply applying the start and stop times to each day, one time schedule can cover the entire week. S ch e d u le X S ta rt S to p M on Tue W ed Thur F ri Sat Sun P a rt. 2 2 :0 0 0 5 :0 0 ON ON ON ON ON OFF OFF 1 4. 8. Multiple Day Rollover The simplest method for defining a window of time that spans multiple days is to use 99:99 to signify an open start or stop time. 9. 1= 2= O ff On Example of Multiple Day Rollover. At your business you'd like specific lights to remain lit from Friday afternoon through the weekend until Monday morning. In this situation, the lights need to be scheduled to roll over until they reach a recognizable stop time. In the figure to the right, Schedule Y is set up to begin at 4 p. m. Since S ch e d u le S ch e d u le the stop time is 99:99, the lights will remain Y Z lit (roll over) until a recognizable stop time is 9 9 :9 9 S ta rt 1 6 :0 0 reached. 0 5 :0 0 9 9 :9 9 S to p Schedule Z is set up with an undefined start ON OFF time (99:99), so if the lights were already lit, M o n they will remain lit until the Schedule Z stop time is reached at 5 a. m. Tue W ed Thur F ri Sat Sun P a rt. 10. Press B to move to the next day of the week or press , to return to the schedule list. Press , + 6 + to exit User Programming. Scheduling Consecutive Days There may be instances when you'd like to schedule a feature event to start one day and stop the next day or a number of days later. One Day Rollover You can create a schedule that begins on one day, and stops the next day by using only one time schedule. (The stop time must be within 24 hours of the start time. ) OFF OFF OFF ON OFF OFF 1 OFF OFF OFF OFF OFF OFF 1 Example 1 of One Day Rollover. At home you'd like the front entry light to be on from 10 p. m. By taking advantage of One Day Rollover, one time schedule can cover both days. [. . . ] The touchpad displays "REGULAR USER CODES. " Press B until the display reads "PARTITION MASTER CODE, " then press . Enter the System Master Code to delete the existing Partition Master Code OR Enter a new 5-digit Partition Master Code to replace the existing code. Press , + 6 + to exit the programming menus. P re ss P re ss P re ss At m ove backw ar th ro u g th e m e n P re ss Bt m o v e fo rw a r th ro u g th e m e n P re ss n k v a lu e ch u m b e re eys w he s orcod o ic e s a r re q u e s te d o d u h C 7 p re s s b o th 2 to tu rn a fe a tu re o n o d 1 to tu rn a fe a tu re o ff e e k ly T e s t S y s te m W u h A O ff H om e Aw ay 1 p re s s b o th 2 S ile n t 3 Pager 4. N o D e la y B p re s s b o th 4 F e a tu re s 5 6 S y s te m M enu 8 9 L ig h ts 5. S ta tu s B ypass D d n * 0 # 6. e e P re ss , t o d e s e le c t a n o p tio n o r to c a n c e l a n e n try To change or delete the Partition Master Code: P r e s s t o s e le c t a n o p tio n o r to a c c e p t a n e n try 1. 3. Examples of Programming Using Menus Here are two examples of programming using system menus. [. . . ]