User manual GE SECURITY RF COMMANDER III

[. . . ] 2 Using the Touchpad Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Using Hand-held Touchpads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using Keychain Touchpads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Be aware of the system devices and how they operate. Always make sure the door is fully closed when entering and exiting the building. Remember to disarm the system if you are interrupted during the entry/exit delay time. Make sure all doors leading outside have delay times. If your system is armed to PERIMETER, an alarm will sound immediately if you open a door that is set to instant. Motion detectors operate by detecting the change in temperature when something passes in front of them. If you have pets, you may want to eliminate motion detectors or ask your dealer to install "pet lenses. " !Check the location of your smoke detectors. Keep in mind that smoke detectors can be activated by sources of steam, smoke, or airborne dust that can occur during normal activities. Manually Resetting Hardwired Smoke Detectors Manually resetting a smoke detector following a test or alarm resets tripped detectors. This procedure is rarely needed because smoke detectors are automatically reset when an alarm is acknowledged or canceled. To manually reset tripped smoke detectors: Steps Response SYSTEM MENU; RESET SMOKE POWER; ENTER YOUR CODE SMOKE LOOP RESET 1. Enter your ACCESS CODE. Note Do not reset smoke detectors until the location of the activated detector is determined and the smoke source removed. System Tampering The system will automatically detect and indicate the type of tampering: !This would allow you to walk from your bedroom to the kitchen or bathroom at night without needing to disarm the entire system. If the phone line is still faulty, the trouble beeps will start again within 24 hours (at the daily trouble indication time). The display continues displaying a flashing * until the trouble is fixed. Arming to Perimeter Arming to Perimeter is used when you stay indoors but want security protection on all doors and windows leading outside. 14 Advent® Commercial System Security Protection To arm the system to perimeter: Steps Response SECURITY MENU; ARMING LEVEL CHANGE; ENTER YOUR CODE; TO QUIT PRESS * PARTITION/AREA X ARMED PERIMETER; OK TO EXIT All sensors will be active except those that are bypassed and those designated indoor sensors preset by your security consultant. Note Protected windows and doors must be either closed or bypassed in order for the system to arm. 1. Press * twice to exit. Arming to Silent Arming to Silent is the same as arming to full except police alarms are silent. To arm the system to silent: Steps Response SECURITY MENU; ARMING LEVEL CHANGE; ENTER YOUR CODE; TO QUIT PRESS * PARTITION/AREA X ARMED SILENT; OK TO EXIT Active sensors: !Outdoor (perimeter door and window) sensors that are not bypassed. Environmental sensors (smoke, heat, carbon monoxide). Arming to Full Arming to Full is used when you leave and no one is supposed to be in or on the premises. To arm the system to full: Steps Response SECURITY MENU; ARMING LEVEL CHANGE; ENTER YOUR CODE; TO QUIT PRESS * PARTITION/AREA X ARMED - FULL; OK TO EXIT 1. Press * twice to exit. All (except bypassed) sensors will be active following an initial exit delay. Note Protected windows and doors must be either closed or bypassed in order for the system to arm. 1. Press * twice to exit. Bypassing A security system cannot protect an open door or window. When you attempt to turn security protection ON, the system will warn you if a door or window has been left open. However, you may want to arm the system anyway. To do this, you must bypass the open door or window. [. . . ] System has taken control of (seized) the telephone lines and/or is too busy to respond now. System is about to take control of (seize) the telephone lines. 30 Advent® Commercial System Appendix D: System Planning Tables Appendix D: System Planning Tables Below are tables to help list programmed options. Schedules Table 12: Schedules Part. # Schedule On Time Off Time Duration Normal Holiday A Holiday B Temporary Arming Type Daylight Type 1 1 Holiday Schedules Advent® Commercial System 31 Appendix D: System Planning Tables Table 13: Holiday Schedule Partition # List Holiday # Month Day Normal 32 Advent® Commercial System FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by Interlogix, Inc. can void the user's authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ]