User manual GEMINI CD-200

[. . . ] CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceiling. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. This state of the art 2U professional CD player is backed by a 3 year warranty, excluding lasers. one year warranty is included for CD lasers. Prior to use, we suggest that you carefully read all the instructions. Plug one end of a set of the included RCA cable connectors into each of the LINE OUTPUT JACKS (3) on the left and right of the main unit's rear panel. Plug the other end of the RCA connectors into any available line level input jacks on your mixer. If you are connecting the CD-200 through a receiver, you can plug the RCA connectors into the CD or AUX INPUT JACKS on your receiver. If there are no CD or AUX INPUTS, use any line level (not phono) inputs. - Audio CD, CD-R compatible - Anti-shock using RAM buffer memory - Instant-start & cue with preview - Single auto-cue/continuous play modes - Seamless loop per side with reloop - Pitch bend via jog wheel or buttons - Three mode time selection - Frame accurate search - Large blue backlit LCD display - Dual mode jog wheels for search or pitch bend - Pitch control with range of +/- 12% - Pitch bend buttons - +10 track button for quick navigation - Fully programmable with repeat function POWER: After making sure that the VOLTAGE SELECTOR SWITCH (1), found on the rear panel of the main unit, is properly set, plug the CD-200 POWER CORD (2) in and press the POWER (5) button. Pushing the POWER button (5) a second time will turn the unit OFF. DISC TRAY: The DISC TRAY (7) is where the CD is held during loading, unloading and playback. Please note, if the CD-200 is in play mode, the tray will not open. OPEN/CLOSE BUTTON: Press OPEN/CLOSE (6) to load or remove a CD from the DISC TRAY. DISPLAY: The DISPLAY (11) shows the track number, pitch value, pitch bend, single, continue (for continuous play), play/pause modes, fast forward/reverse modes, loop mode, reloop mode, PGM, repeat modes, the playback display bar, and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. time is measured in minutes , seconds and frames. The PLAYBACK DISPLAY BAR, located at the top of the DISPLAY (11), displays the elapsed and remaining time for each track at the very top of the display. The display flashes slowly when the track has 15 seconds remaining and pulses rapidly when playing time is down to 5 seconds. PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (20) causes the operation to change from PLAY to PAUSE or from PAUSE back to PLAY. The green PLAY/PAUSE LED remains lit when in PLAY mode, while it blinks in PAUSE mode. This button will also erase any CUE and LOOP settings. [. . . ] Before plugging this unit into any outlet, make sure that the VOLTAGE SELECTION SWITCH (1) is set to the proper voltage. To change the selection, unscrew the hard plastic protective top with a Phillips head screw driver. When you have selected the proper track, press PGM (16) and the CD-200 will be ready to set your next selection. Repeat steps 2-4 until you have completed your set list, and press play to begin the set list. [. . . ]