User manual GEMINI GEM-P400

[. . . ] Using Your GEM-P400 Security System GEMINI TUS STA ED ARM &20387(5, =(' 6(&85, 7< 6<67(0  1 2 3 4 Oi230a page 1 Tuesday, September 16, 1997 08:26 Oi230a page 2 Tuesday, September 16, 1997 08:26 Introduction Congratulations on your purchase of an advanced GEMINI-P400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you and all potential users of the system familiarize yourselves with its operation, and can therefore take full advantage of GEMINI's many convenience features and amenities. [. . . ] If your system has the Ambush feature enabled, the code assigned as the User 4 code will function as your Ambush Code. Yes 8 Oi230a page 8 Tuesday, September 16, 1997 08:26 Disarming Your System / Silencing an Alarm Disarming Your System when Returning 1 2 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. The red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press re-enter the code, followed by. and Alarm Indication If the Red Armed light is flashing rapidly, an alarm occurred while you were away. For your own protection, leave immediately and call authorities from a neighbors phone . Silencing an Alarm In the event that the system goes into alarm due to a violated burglary zone, the siren and the keypad sounder will activate and the number of the zone in alarm will flash in the display. To silence the system, enter your User code followed by . The keypad sounder and siren will silence, but zone in alarm will continue to flash. Press o reset this alarm memory. t 9 Oi230a page 9 Tuesday, September 16, 1997 08:26 Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by followed by . This will allow the easy pressing arming of the system by someone who is not a regular system user. Simply press trouble as described below, and then arm the system. To determine the nature of the trouble, press ollowed by count the number of keypad beeps and observe the number of the illuminated zone. Refer to the following table to determine the cause of the trouble. If there is more than one trouble to view, will scroll to the next trouble, and then exit the TROUBLE mode if there are no more troubles to view. pressing Keypad Beeps or lashes 1 Beep F f , followed by t o view the Zone light ON 1 System Trouble Condition AC Power Failure Action This trouble will occur if AC power is not present. Make sure system transformer is plugged into AC receptacle and check the circuit breaker, otherwise call installing company for service. If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control panel. If the trouble does not go away in 24 hours, call installing company for service. The system was not able to report to central station. If this is due to a temporary interruption in the telephone service, the trouble can be cleared when the service is restored by pressing ollowed by again to view the trouble, and and then o exit. Otherwise, call installing company for service. If telephone service has been temporarily interrupted, the trouble will clear it is when restored. Otherwise, call installing company for service. There is a problem with the Bell or Siren. [. . . ] After repair or replacement, NAPCO assumes the cost of returning products under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges. This warranty contains the entire warranty. [. . . ]