User manual GEMINI MM-01

[. . . ] ATTACHMENTS: Do not use attachments not recommended by the product manu facturer as they may cause hazards. WATER AND MOISTURE: Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. ACCESSORIES: Do not place this product on an unstable cart, stand, tripod, brack et, or table. The product may fall, causing serious injury to a child or adult, and seri ous damage to the product. [. . . ] Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal oper ation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance, this indicates a need for service. REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceil ing. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as This state of the art mixer is backed by a three year warranty, excluding crossfader and channel slides. The crossfader and channel slides are backed by a separate 90 day warranty. Prior to use we suggest that you carefully read all the instructions. - 4U 19" Rack Mounted Club Mixer - 4 Stereo Channels - 7 Line, 2 Mic, 2 Convertible Phono/Line, RCA Inputs - 5 Band Master Graphic EQ - Fully Removable, User Replaceable Rail Glide Cross Fader - Dual Display with Bright LED - XLR Mic Input with 2 Band Rotary EQ Control - Rotary Mic Volume Control - Auto Talk-Over Feature - Push-Button Cueing with Cue/PGM Fader Control - Master and Record RCA Outputs - Top Located 1/4" Headphone Input Flip the switch(es) down to operate through LN 2 or LN 4. The PH INPUTS only accept turntables with a magnetic cartridge. When using (a) turntable(s), you will need to ground the RCA cable(s) by screwing in the grounding fork(s) to the GROUNDING SCREW (5) located in the rear panel of the MM-01 mixer. This is located in between the CONVERTER SWITCHES (6, 7). The STEREO LN INPUTS only accept line level inputs such as a CD, DAT, MiniDisc, etc. Headphones may be plugged into the face-plate located 1/4" HEADPHONE (20) JACK. Once all of your connections have been in the rear panel, turn on the mixer by pressing the POWER SWITCH (39). CHANNEL 1: To bring this channel in to program output (PGM), you must first decide which line will be in use. Use the LNSWITCH (23) to toggle from LN 1 (4) to Mic 2 (14) on this channel. Slowly raise the CH1 SLIDE CONTROL (25) to a comfortable level, once you've selected the proper line. [. . . ] Located on the rear panel are 2 Phono/Line convertible RCA inputs (8, 9), and 5 line RCA inputs (12, 13, 11, 10, 4). The convertible RCA inputs (8, 9) for Channels (CH) 2(28) & 3(31) allow Phono (PH) and Line (LN) level equipment to be connected to the mixer. CROSSFADER SECTION: The CROSSFADER (38) allows you to mix from one source to another. CH 1 (25) and CH 4 (34) are controlled through their respective SLIDE CONTROLS (25, 34) and not the CROSSFADER (38). [. . . ]