User manual GEMINI PS-02

[. . . ] CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceiling. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Congratulations on your purchase of a Gemini PS-02 professional 10" 3 channel stereo mixer. This state-of-the-art mixer features the latest technological advances and is backed by a three year warranty, excluding the cross fader. The cross fader is backed by a separate 90 day warranty. Prior to use we suggest that you carefully read all the instructions. - The BALANCED MASTER OUTPUT (8) connects the mixer to your main amplifier using standard cables with 1/4" connectors. We recommend using balanced cables if the distance to your amp is 10 feet or more. - The ZONE (7) output jacks allow the connection of an additional amplifier with RCA cables. - The REC (6) output jacks can be used to connect the mixer to the record input of your recording unit, thus enabling you to record your mix with RCA cables. Headphones may be plugged into the front panel-mounted HEADPHONES (22) ¼" jack. Microphones may be plugged into the front panel-mounted MICROPHONE (21) ¼" jack. Using the PH/LN CONVERTERS (11, 15, 19), located just below each input, you may convert the PH to LN and vice versa. Plug the RCA's from your playable medium into each input to be connected to their respective CHANNELS (CH). The PH INPUTS (10, 14, 18) only accept turntables with a magnetic cartridge. The STEREO LN INPUTS (9, 10, 13, 14, 17, 18) only accept line level inputs such as a CD, DAT, Mini Disc, etc and require the proper switch settingand require the LN switch setting as indicated in the PH/LN CONVERTER SWITCHES (11, 15, 19). When using (a) turntable(s), you will need to ground the RCA cable(s) by screwing in the grounding fork(s) to the TRIPLE GROUNDING SCREWS (12 , 16, 20) located in the rear panel of the PS-02 mixer. Attach each PH ground lines to one of the TRIPLE GROUND THUMB SCREWS (12, 16, 20). These are to the right of each PH/LN CONVERTER (11, 15, 19). - 10" 3 stereo channel mixer - 6 line, 3 convertible phono/line, RCA inputs - Master, record, & zone RCA outputs - ¼" balanced outputs - Triple ground screw for easy connectivity - Removable face plate for user replaceable Rail Glide cross fader - 3 band EQ kill switches with flash effect - 3 band rotary line EQ with cut feature & rotary gain channel control - Lighted push button cue section - Rotary zone & balance controls - Dual VU display with bright LED & mode switch - Master volume fader control - ¼" headphone output & Mic input - Cue section with rotary cue volume & CUE/PGM controls with Split/Cue/Mix switch - Mic section with rotary Mic volume, high & low EQ controls - Fader section with hamster/reverse, slope, & assign switches All instructions should be read before using this equipment. To reduce the risk of electrical shock, do not open the unit. Do not expose this unit to direct sunlight or a heat source such as a radiator or stove. [. . . ] also available is our RG-45 PRO (PROGLIDETM) Dual-Rail CROSS FADER. This unique CROSS FADER features, a special curve designed for scratch mixing. Just purchase one from your Gemini dealer and follow the instructions: Flip the CROSS FADER SLOPE SWITCH (57) down to make the slope steep and cutting (perfect for scratching). REVERSE CONTROL: The CROSS FADER REVERSE SWITCH (56) allows you to reverse the CROSS FADER so that the right side CH2 (36) or CH3 (43) is controlled by the left side of the CROSS FADER (46) and the left side CH1 (29) or CH2 (36) is controlled by the right side of the CROSS FADER (46). [. . . ]