User manual GENIUS HR8

[. . . ] User's Guide Genius Scanner All trademarks and brand names mentioned in this publication are property of their respective owners. 2003 KYE Systems Corp. No portion of this document may be reproduced without permission. Table of Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Conventions of this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Adjust the scanning border, if necessary. 5. 6. 7. Genius Scanner 14 8. Click on the SCAN IMAGE icon to start scanning the image. Important Notes about Scanning Film Do not cover any small compartment below each arrow sign on the film holder because that it is necessary for calibration. Always replace the reflective document mat onto the scanner's document cover after you finish scanning the films. Make sure the film is properly loaded into the film holder and the film holder is correctly positioned on the scanner glass. Make sure the proper SCAN SOURCE and SCAN SIZE are selected before proceeding the scanning task. It is recommended to use a higher resolution (such as 600dpi for 35mm films, or 300dpi for 120/220 films) when you proceed the film scanning task to prevent the scan images from losing the quality while you enlarge the size of the images. Sound Settings You may choose to play a sound file when executing any scanning task to add fun and pleasure. To personalize your sound effect, please adjust the settings within the Sound Settings window as described below: 1. Click on the Windows START button and then PROGRAMS, COLORPAGEXXXX (your scanner model name) and then Sound Settings. Within the Sound Settings window that opens (as shown below), click the option of "DISABLE" to turn off the sound effect or "ENABLE" to turn it on. 2. 15 Genius Scanner 3. If you enable the sound effect, click on the "BROWSE" button to select the desired sound file from your hard disk drive. The full file path and name of the selected sound will be shown on the left of the Browse button. Click on the "START PLAYING" button , if you desire to play the sound immediately and verify your choice. Click on the "STOP PLAYING" button to stop playing the sound. Repeat this until you decide the sound file. 4. 5. Click on the "OK" button to save the settings and close this window, or click on the "CANCEL" button if you would like to close the window and abort settings done. Attention Note: Note: To play MIDI and MP3 files with this scanner, your Windows system must be installed with Media Player 7. 0 (or later version). Scanner Utility Program The Scanner Utility Program can help you get your new scanner up and running. In addition, it contains a number of other features to help you tailor and control the scanner. Most significantly, the Scanner Utility Program checks to make sure that the scanner software is properly installed and the scanner and computer are communicating with each other. Two other features of the Scanner Utility program are the scanning lamp controls and the scanning position alignment utility. The Scanner Utility allows you to turn the scanning lamp on and off, and define an idle time for the scanning lamp to automatically turn itself off. Also, it allows you to define the exact position on the scanning glass where scanning will begin. The scanner lock was designed to hold the scanning lamp in place during shipping, but some refinement of the initial scanning position may still be necessary. Genius Scanner 16 Turn Lamp On/Off Verify Scan Alignment Window Alignment Position Attention The Scanner Utility program does NOT affect the quality of scanned images. It is only used to establish a connection with the scanner. Settings that affect the scanned image (i. e. , color, size, readability, clarity, etc. ) can be found in the scanner software programs and especially the TWAIN interface. Connection Status The first step to take when troubleshooting connection problems with your scanner is to check all physical connections. Make sure your scanner is plugged in and the USB cable is fit snugly into the rear of your scanner and computer. [. . . ] Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply. Under no circumstances are we liable for any of the following: Third party claims against you for losses or damages. Loss of, or damage to, your records or data; or Economic consequential damages (including lost profits or savings) or incidental damages, even if we are informed of their possibility. Some jurisdictions do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you. [. . . ]