User manual GEONAUTE WATCH CHRONO 900

[. . . ] Chrono 900 FR-EN-ZH. qxd 8/06/05 10:08 Page 66 Chrono 900 FR-EN-ZH. qxd 8/06/05 10:08 Page 18 RECALL SPLIT/RESET START/STOP DÉCATHLON guarantees the initial purchaser of this stopwatch that it is free from any faults linked to the materials or manufacture for a period of two years from the date of purchase. Please retain your receipt as proof of purchase. This guarantee does not cover damage resulting from improper use, failure to respect the terms of use or accidents, neither does it cover damage resulting from improper maintenance or use of the item for business purposes. . This guarantee does not cover damage resulting from repairs carried out by parties not authorized by DÉCATHLON. [. . . ] button Press the SPLIT/RESET to scroll through the pacer values incrementally. Press RECALL to scroll downwards. · Press the START/STOP button to start or stop the pacer. If the first countdown is not T1, the repetition counter increases by 1 just before beginning again with the countdown from the beginning (ex: 3 countdowns, T1, T2, T3 have been programmed. The counter is therefore increased after having completed T3, then T1, then T2, and just before beginning T3 again). value · Settingathe starting(2s) onof the countdown The indication of the set value will flash Press for longer time the RECALL button. to indicate that you have entered the setting mode. . Press repeatedly on the SPLIT/RESET button to change the parameter to set following the sequence . . . hour-minutes-seconds. . . When one of the elements flashes, press the START/STOP button to make the numbers scroll until you reach the desired value. Press RECALL again to leave the setting mode. Repeated timer (symbole ) · Use The START/STOP button starts or stops the countdown. When the countdown has stopped, press the SPLIT/RESET button to reinitialize it at its set value. When the count arrives at 0, a 5 second buzz is emitted. The repetition counter (between the square brackets) goes up by 1 unit. Then the countdown begins with its initial value and counts down the same interval of time again. A press on the START/STOP button will stop the counting. A press on SPLIT/RESET will reset the repetition counter to 0 and reinitialize the countdown at its starting value. value · Settingathe starting(2s) onof the countdown The indication of the set value will flash Press for longer time the RECALL button. to indicate that you have entered the setting mode. Press repeatedly on the SPLIT/RESET button to change the parameter to set following the sequence . . . hour-minutes-seconds. . . When one of the elements flashes, press the START/STOP button to make the numbers scroll until you reach the desired value. Press RECALL again to leave the setting mode. Training timer (symbole ) · · Buzzers : auditorily between the types of buzzing for countdowns and for the To differentiate progression of the session, the final beeps have been differentiated: End of a countdown: 3 beeps in close succession. End of a repetition: 2*3 beeps in close succession End of the session: 4*3 beeps in close succession For the preceding example : Start !3 beeps in close succession Timer 2 : 15s. [. . . ] With each press, the intermediate time counter goes up by one. Once the number 299 is reached, the counter will flash to signal that the memory is full. When the stopwatch has stopped (START/STOP), the last lap is put into memory. ATTENTION : When the speed calculation (SPEED, see corresponding mode) is in progress, the stopwatch function cannot be used. 6 Speed Calculation Mode (SPEED) 00:00':00''00 [000] LAP STOP 00:00':00'0' 0 0, 161'0' 0 Km FULL SPEED TIME DIST START/STOP : Start / Stop the count (remember: you cannot start if the distance is set at 0) SPLIT/RESET : if the stopwatch is functioning: time elapsed if the stopwatch has stopped: reset to zero RECALL : if the data have been stored in memory: enables you to enter the memory recall mode if the time has been reset to zero, hold the button down now for 2 seconds: enables you to enter the distance setting mode. MODE : go to the following mode ATTENTION : Since the maximum speed display is 999, 999, if the calculated speed is larger than this value, "ERROR" will be displayed on the top line, and the value of the speed will not be recorded in the memory. · When you are using this mode, the value for the distance cannot be zero. [. . . ]