User manual GERICOM 1XP

[. . . ] 72-11P00-013 Printed in Taiwan Notice The manufacturer reserves the right to make any updates, revisions or changes to the information contained herein as and when deemed necessary. The manufacturer is under no obligation to notify any purchaser or end-user of such actions in advance or afterwards. 1998 Trademarks IBM PC, PS/2, EGA, and VGA are registered trademarks of International Business Machines Corporation. Intel, Pentium are trademarks of Intel Corporation. [. . . ] Turn on the printer and Notebook Computer. In addition, you will need to install the manufacturer-supplied driver for the printer. Refer to the device's user's guide for more information. If the connected printer supports EPP (Enhanced Parallel Port) or ECP (Extended Capabilities Port) mode, please enter System Configuration Utility (SCU) to configure the required setting. Figure 2-24 User's Manual 2-35 Attaching an External Monitor (CRT) The computer is capable of displaying information not only on the LCD, but also on SVGA compatible displays attached to the computer. Information can be displayed on both the LCD and the external monitor simultaneously. Enter the System Configuration Utility (SCU) to select the appropriate parameters or use the Fn + F6 keys (refer to Chapter 2, Using Hot Keys). Connect the cable to the CRT port on the rear of the Notebook Computer (Step 1 in Figure 2-25). Tighten the screws that fasten the cable to the CRT port (Step 2 in Figure 2-25). Insert the other end of the cable to the external monitor. Turn on the Notebook Computer. Figure 2-25 Chapter 2: Operation 2-36 Attaching a Proprietary Port Replicator The proprietary Port Replicator, providing interfaces for those found on the Notebook system, frees you from fumbling with multiple cables every time you leave the office. Please contact your dealer for detailed information. Figure 2-26 User's Manual 2-37 Attaching a Video Input Device The RCA jack on the rear panel of the Notebook allows analog composite signal input from external video devices. Attach the device as shown below (Figure 227). Figure 2-27 Chapter 2: Operation 2-38 Attaching a TV Set The S-video jack on the rear panel of the Notebook is used for transmitting video signals to a TV set. You may need to select the video standard for video display. Enter the System Configuration Utility (SCU), Components Menu to specify the appropriate TV mode. Simultaneous display on external monitor (CRT) and TV is available. You may enter the SCU to select the appropriate parameters or use the Fn + F6 keys (refer to Chapter 2, Using Hot Keys). Attach the TV set as shown below (Figure 2-28). Figure 2-28 User's Manual 2-39 Attaching a USB-compatible Device The Notebook provides a USB port for connection of a USB-compatible keyboard, mouse or other devices. Attach the device as shown below (Figure 229). Figure 2-29 Chapter 2: Operation 2-40 User's Manual 3-1 Chapter 3: BIOS Utilities This chapter provides information regarding the Power On Self Test (POST) and shows you how to configure the system parameters using the System Configuration Utility (SCU). Power On Self Test (POST) POST Message: Normal Operation POST Message: Error Detected System Configuration Utility Information in the System Configuration Utility Initiating the System Configuration Utility Initiating the System Configuration Utility Working with the Menu Bar of the SCU Working with the Pull-down Menu of the SCU Features of the System Configuration Utility Startup Menu Memory Menu Disks Menu Components Menu Power Menu Exit Menu Chapter 3: BIOS Utilities 3-2 Power On Self Test (POST) The system BIOS (Basic Input/Output System) performs a series of Power On Self Test (POST) on system memory and key computer components every time the computer is turned on. If an error exists, the POST routine may halt execution (depending on the severity of the problem). The POST also initializes BIOS configuration then boots the operating system. POST Message: Normal Operation If no error occurs, the system will be operating after the POST process is completed. You may press the Spacebar key to skip the memory test. SystemSoft MobilePRO BIOS Version 1. 01 (2482-00) Copyright 1983-1996 SystemSoft Corp. All Rights Reserved 233 MHz Pentium with MMX CPU External Cache: 512KB installed 4 MB Video RAM SystemSoft Plug-n-Play BIOS Ver. 1. 17. 01 Base Memory Extended Memory Total Memory 000640 Kb 064512 Kb 065536 Kb Auto Detecting IDE Devices[Done] <CTRL-ALT-S> to enter System Configuration Utility User's Manual 3-3 POST Message: Error Detected If an error is detected, a WARNING message will be displayed. [. . . ] Under Win95, click [Start], [Run] and open the path [D:\AtiDVD\Setup. exe]. User's Manual [c:\windows\system\pccard. vxd] [ c:\windows\inf\pcmcia. inf] 5-7 Step VIII: Using Infrared Wireless Communication Please refer to the read-me file under the FIR directory. Drivers for Windows 98 Step I: VGA Driver Installation After installing Win98 successfully, enter into the system. Click [Start] at the bottom-left corner on the Windows screen; select [Run]; open the path of [D:\WIN9X\setup. exe] to run VGA driver installation. When ATI VGA driver has been already included in the system, click [Start], select [Run] and open the path of [\atiuinst-clean] and doubleclick [Ok]. Note: For system ATI VGA included, uninstall the original VGA Driver and then install the driver. [. . . ]