User manual GIANT BICYCLES CONTINUUM WIRELESS

[. . . ] CONTINUUM W 1 2 3 4 SET SW. CYCLE COMPUTER Press down on this lock lever before removing the main unit. 12 11 9 18 Magnet center aligns to the marking line. Gap <5mm (0. 2") 14 Slide On PRESS 14 13 8 6 BRACKET 5 15 12 11 13 14 16 8 9 A G * Adjust the arm, elbow and bracket with the angle you need, and then fasten it. Lever B H C I FORK 17 D J 12 FORK E K Shorter screw COIN F L 10 16 45cm L < et) 90 A <+ 15 3 (1. 5 fe 10 Best direction 6 PULL 15 12 9 6 7 17 18 A. Install the sensor as close to the main unit as possible and no more than 45 cm (1. 5 feet) to improve wireless performance. The computer will function with the sensor arrow pointed down (Fig. H), but by pointing the arrow up the performance will be improved by reducing the transmitting distance. [. . . ] Wheel Circumference Setting: 1mm - 3999mm (1mm increment) Operation Temperature: 0 C ~ 50 C (32 F ~ 122 F) Storage Temperature: - 10 C ~ 60 C (14 F ~ 140 F) Main Unit Battery Power: 3V battery x 1 (CR2032), battery operating life is about 2 years. (Based on an average of 1. 5 hours use per day) Transmitter Battery Power: 1. 5V battery x 1 (typical LR44). About 24. 000km/15. 000 miles riding distance or 2 years battery operating life. (The original factory-attached battery life may be shorter than this period due to shipping and storage time). Dimensions and Weight: Main Unit: 44. 0 x 54. 5 x 19. 73mm/30. 8g Transmitter: 20. 0mmo x 48. 0mm/13. 3g * The specifications and designs may be changed without notice. INDEX: a 2 SEC Means press button more than 2 seconds. 741) Means press button 1 quickly. ALL CLEAR N=KEY NUMBER: ( :Mode Button; :Set Button) ODO SETTING DATA SETTING PROCESSES (621 UNIT SELECTION CIRCUMFERENCE SETTING b CLOCK SETTING NORMAL OPERATION D 2 Clock Odometer 2 SEC MODE 3 S EC +1 +1 +1 SET LCD SEGMENTS AUTO TEST D RESET (TM=0, DST=0, MAX=0, AVG=0) D 4 2 S EC D OK Trip time Distance Max speed Average speed Distance per day 3 2 S EC CLOCK RE-SETTING RIDING STATUS 2 S EC D INDEX: N MEANS PRESS BUTTON N MORE THAN 2 SECONDS. N MEANS PRESS BUTTON N QUICKLY {N=KEYNUMBER: 2 MODE Button. A battery is already loaded in the main unit when purchased. Hold down the MODE button 2 and SET button 4 simultaneously for more than 3 seconds to initiate the computer and clear all data. IMPORTANT: Be sure to initiate the computer before it is be used, otherwise the computer may run errors. The LCD segments will be tested automatically after the unit is initiated. Press the MODE button 2 to stop LCD test, then the flickering "KM/h". UNIT SELECTION Press MODE button 2 to choose KM/h or M/h (Mile/h). Press the SET button 4 to select either as desired. This function is designed to re-enter ODO data when battery is replaced. New users do not need to enter this setting. Pressing the SET button 4 skips one step in the set-up process. Data Entry Processes (621 741): (Fig a) A. Press the MODE button 2 to increase the value by 1. Advance to the next digit by holding down the MODE button 2 for more than 2 seconds. Press the SET button 4 to store the data and change to the next setting. "c2155"is displayed as the default value 2155mm. Measure the circumference of your wheel or refer to the quick reference table provided in this manual. [. . . ] To preserve the battery, this computer will automatically power down into a sleep mode. Only the " " data will be displayed when it has not been used for about 30 minutes. Power up by pressing the MODE button 2 . Press the MODE button 2 to change to one of the following mode displays. [. . . ]