User manual GIGABYTE 3D GALAXY II

[. . . ] (Please purchase GIGABYTETM liquid coolant to fill it. ) 3. When the liquid is lower than the low water-level, the system will turn off automatically within four seconds after detection of water inadequacy. While removing the tubes for disassembly, please make sure to keep all the devices away from any electronic part. [. . . ] 4. Aluminum 4-way water path design radiator with 12 cm adjustable fan for lower noise. 6 English 5. Delicate sparkly blue LED light design tank; easy refilling coolant. 6. Well-executed liquid cooling radiator fits most existed PC chassis. 7. Multipurpose nanometer GIGABYTETM coolant. 8. 1/2inch UV soft tube; unique design to reduce bending needs. 9. Fully support cooling solution for the surrounding component of CPU (Mosfet). 10. GIGABYTETM excusive 4-way splitter valve design for faster replacement and add new cooling equipment. 11. PCI Rear Fan Speed Controller 12. Free heat sink for memory 13. Wide range use for AMD K8/AM2;Intel® Pentium® 4 LGA 775. <Recommended chassis to use: GIGABYTETM 3D Aurora, Triton, Poseidon series Chassis> 4. Liquid Cooling System Installation Please follow the instruction. 4-1 Installation Preparation Please make sure the power of PC has been turned off. Tool needed: scissors, GIGABYTETM coolant, grease, screwdriver. 4-2 Intel Pentium 4 LGA775 Back Plate Installation (For AMD series CPU, please ignore this step) 4-2-1 Take off the double-side sticker on the Intel Pentium 4 LGA775 Back Plate (as ® ® Figure a), and stick it on the back of Intel Pentium 4 LGA775 CPU with aligning ® ® four holes on Intel Pentium 4 LGA775 Back Plate and four holes on the back ® ® of Intel Pentium 4 LAG775 CPU motherboard (as Figure b). ® ® ® ® Figure a Figure b 7 English 4-3 PCI Rear Fan Speed Controller Installation (as Figure a/b) 4-3-1 Place PCI rear fan speed controller to the back of the chassis (place on the lower PCI is recommended as Figure c. ) Figure a Figure b Figure c 4-4 Tube Installation After measuring the distance between each parts of the cooling system, cut the tubes into five suitable sizes as it shows below. To get the right length for each tube, strongly recommend to fit all the components in the right position. Liquid Cooling System complete installation diagram. Tube3: The inlet of radiator to 4-way splitter valve (1) B Tube4: The outlet of radiator to the inlet of the tank A Tube1: 4-way splitter valve (1) to the outlet of the waterblock B A Tube2 : 4-way splitter valve (2) to the inlet of the waterblock Tube5 : 4-way splitter valve (2) to the outlet of the tank 8 English Tube1 Tube3 Tube4 Tube2 Tube5 While placing tube, please do not bend the tube in order to avoid obstructing water flow (as the right Figure under). Besides, if needed, please use bend proof spring on the tube while bending it to avoid obstructing water flow efficiency. 4-5 4-way Splitter Valve to the Tube on Waterblock Installation 4-5-1 Connect one side of tube 1 to 4-way splitter valve (1) A as it shows in the picture and fasten the tube clip. 4-5-2 Connect the other side of tube 1 to the outlet of waterblock and fasten the tube clip. O O X 9 English 4-5-3 Connect one side of tube 2 to 4-way splitter valve (2) B as it shows in the figure and fasten the tube clip. 4-5-4 Connect the other side of tube 2 to the inlet of waterblock and fasten the tube clip. The 2 splitters in the middle of 4-way splitter valve can be used to support VGA, chipset liquid cooling system or other liquid cooling system. If the 2 splitters in the middle of 4-way splitter valve are available, please do not take off the cap and switch them to horizontal to avoid leakage. 4-6 4-6-1 Radiator to 4-way Splitter Valve Installation Thread Tube 3 through the hole on PCI slot (as Figure a) to connect one side of tube 3 to 4-way splitter valve (1) B and fasten the tube clips (as Figure b). Figure a Figure b Figure c For GIGABYTETM 3D Aurora, Triton or Poseidon series user, the tube can be threaded through drainage inlet/outlet on the chassis. ( as the two holes on the right in Figure c ) 10 English 4-6-2 Connect the other side of tube 3 to the inlet of radiator and fasten the tube clips. 4-7 Radiator to the Inlet of Water Tank 4-7-1 Thread Tube 4 through the hole on PCI slot to connect one side of tube 4 to the outlet of radiator and fasten the tube clips. Connect the other side of tube 4 to the inlet of the tank and fasten the tube clips. 4-7-2 4-8 4-way Splitter Valve to the Outlet of Water Pump 4-8-1 Connect one side of tube5 (as Figure shown) to 4-way splitter valve(2) and fasten the tube clips. [. . . ] 4-way Splitter Valve Instruction and User Manual (Adding VGA waterblock and chipset waterblock without disassembly) Ex. GIGABYTETM blue eye and chipset waterblock Please make sure to turn off PC power before installation. 7-1 Remove the caps and tube clips from 4-way splitter valve. Do not switch on at this point. 7-2 Cut a tube into suitable size; connect one side of the tube with the first splitter on 4-way splitter valve(1) and connect the other side with the inlet of VGA Blue Eye and fasten the tube clips. Cut a tube into suitable size; connect one side of the tube with the second splitter on 4-way splitter valve(2) and connect the other side with the outlet of VGA Blue Eye and fasten the tube clips. 7-3 22 English 7-4 Cut a tube into suitable size; connect one side of the tube with the second splitter on 4-way splitter valve(1) and connect the other side with the outlet of chipset waterblock and fasten the tube clips. 7-5 Cut a tube into suitable size; connect one side of the tube with the first splitter on 4-way splitter valve(2) and connect the other side with the inlet of chipset waterblock and fasten the tube clips. [. . . ]