User manual GIGABYTE 8I845PE-RZC

[. . . ] Intel® Pentium® 4 Processor Motherboard 8I845PE-RZ / 8I845PE-RZ-C User's Manual Rev. 1002 12ME-I845PERZ-1002 Copyright © 2004GIGABYTE TECHNOLOGYCO. , LTD Copyright by GIGA-BYTETECHNOLOGY CO. , LTD. No part of this manual may be reproduced or transmitted in any from without the expressed, written permission of GBT. Trademarks Third-party brands and names are the property of their respective owners. Notice Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet. [. . . ] (Default value) All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all other errors. Memory The category is display-only which is determ ined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K m emory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the am ount of mem ory located above 1 M B in the CPU's memory address map. 8I845PE-RZ Series Motherboard - 22 - Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features First Boot Device Second Boot Device Third Boot Device Boot Up Floppy Seek Password Check CPU Hyper-Threading Init Display First [Floppy] [HDD-0] [CDROM] [Disabled] [Setup] [Enabled] [AGP] Item Help Menu Level} Select Boot Device priority [Floppy] Boot from floppy [LS120] Boot from LS120 [HDD-0] Boot from First HDD [HDD-1] Boot from Second HDD higf : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Save Default ESC: Exit F1: General Help F7: Optimized Defaults English # " # " System will detect automatically and show up when you install the Intel® Pentium ® 4 processor with HT Technology. First / Second / Third Boot Device Floppy LS120 HDD-0~3 SCSI CDROM ZIP USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Select your Select your Select your Select your Select your Select your Select your Select your Select your Select your Select your Select your boot device priority by Floppy. boot device priority by Disabled. Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks 720K, 1. 2M and 1. 44M are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720K, 1. 2M or 1. 44M drive type as they are all 80 tracks. Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360K. (Default value) Password Check System Setup The system can not boot and can not access to Setup page will be denied if the correct password is not entered at the prompt. The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. (Default value) - 23 - BIOS Setup English CPU Hyper-Threading Enabled Disabled Enables CPU Hyper Threading Feature. Please note that this feature is only working for operating system with multi processors mode supported. (Default value) Disables CPU Hyper Threading. Init Display First Select the first initation of m onitor or display from AGP or PCI VGA card. (Default value) PCI Set Init display first to PCI. Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals On-Chip Primary PCI IDE On-Chip Secondary PCI IDE IDE1 Conductor Cable IDE2 Conductor Cable USB Controller USB Keyboard Support USB Mouse Support AC97 Audio Onboard H/W LAN * Onboard LAN Boot ROM * Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode x ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ higf : Move Enter: Select F5: Previous Values [Enabled] [Enabled] [Auto] [Auto] [Enabled] [Disabled] [Disabled] [Auto] [Enabled] [Disabled] [3F8/IRQ4] [2F8/IRQ3] [378/IRQ7] [SPP] 3 [201] [330] [10] +/-/PU/PD: Value F10: Save F6: Fail-Save Default Item Help Menu Level} [Auto] Auto-detect IDE cable type [ATA66/100/133] Set Conductor cable to ATA66/100/133(80 -pins) [ATA33] Set Conductor cable to ATA33(40-pins) ESC: Exit F1: General Help F7: Optimized Defaults On-Chip Primary PCI IDE Enabled Disabled Enabled Disabled Auto ATA66/100 ATA33 Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. (Default value) Disable onboard 2nd channel IDE port. (Default value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is com patible with ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). On-Chip Secondary PCI IDE IDE1 Conductor Cable IDE2 Conductor Cable Auto Will be automatically detected by BIOS. (Default value) ATA66/100 Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is com patible with ATA66/100). ATA33 Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). "*" For 8I845PE-RZ only. 8I845PE-RZ Series Motherboard - 24 - USB Controller Enabled Disabled Enabled Disabled Enabled Disabled Enable USB controller. [. . . ] n Intel Application Accelerator Designed to improve performance of the storage sub-system and overall system performance. n USB Pacth for WinXP This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP. n RealTek LAN Driver * RealTek 10/100 LAN driver for 81xx series chips. n C-Media AC97 Audio Driver Install C-Media AC97 audio driver. [. . . ]