User manual GIGABYTE 8S651M-RZC

[. . . ] Intel Pentium® 4 Processor Motherboard 8S651M-RZ / 8S651M-RZ-C User's Manual Rev. 1001 12ME-8S651MRZ-1001 Copyright © 2003GIGABYTE TECHNOLOGYCO. , LTD Copyright by GIGA-BYTETECHNOLOGY CO. , LTD. No part of this manual may be reproduced or transmitted in any from without the expressed, written permission of GBT. Trademarks Third-party brands and names are the propertyof their respective owners. Notice Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet. [. . . ] (Default value) Drive A is 3 mode Floppy Drive. Drive A & B are 3 m ode Floppy Drives. Halt on The category determines whether the computer will stop if an error is detected during power up. No Errors The system boot will not stop for any error that m ay be detected and you will be prompted. All Errors Whenever the BIOS detects a non-fatal error the system will be stopped. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all other errors. Memory The category is display-only which is determ ined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K m emory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the am ount of mem ory located above 1 M B in the CPU's memory address map. 8S651M-RZ Series Motherboard - 24 - Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features First Boot Device Second Boot Device Third Boot Device Boot Up Floppy Seek Password Check [Floppy] [HDD-0] [CDROM] [Disabled] [Setup] Item Help Menu Level} Select Boot Device priority [Floppy] Boot from floppy [LS120] Boot from LS120 [HDD-0] Boot from First HDD [HDD-1] Boot from Second HDD higf : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Save Default ESC: Exit F1: General Help F7: Optimized Defaults English First / Second / Third Boot Device Floppy LS120 HDD-0~3 SCSI CDROM ZIP USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Select your Select your Select your Select your Select your Select your Select your Select your Select your Select your Select your Select your boot device priority by Floppy. boot device priority by Disabled. Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks 720K, 1. 2M and 1. 44M are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720K, 1. 2M or 1. 44M drive type as they are all 80tracks. Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360K. (Default value) Password Check System Setup The system will not boot and will not access to Setup page if the correct password is not entered at the prompt. The system will boot but will not access to Setup page if the correct password is not entered at the prompt. (Default value) - 25 - BIOS Setup English Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals IDE1 Conductor Cable IDE2 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE AC97 Audio Onboard LAN Device (* ) System Share Memory Size USB Controller USB Legacy Support Init Display First Onboard Serial Port A Onboard Serial Port B Serial Port B Mode Onboard Parallel Port Parallel Port Mode x EPP Mode Select ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ higf : Move Enter: Select F5: Previous Values [Auto] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] [32MB] [Enabled] [Disabled] [AGP] [3F8/IRQ4] [2F8/IRQ3] [Normal] [378/IRQ7] [ECP] EPP1. 7 [3] [201] [330] [10] +/-/PU/PD: Value F10: Save F6: Fail-Save Default Item Help Menu Level u [Auto] Auto-detect IDE cable type [ATA66/100/133] Set Conductor cable to ATA66/100/133 (80-pins) [ATA33] Set Conductor cable to ATA33(40-pins) ESC: Exit F1: General Help F7: Optimized Defaults IDE1 Conductor Cable Auto ATA66/100/133 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100/133 (Please m ake sure your IDE device and cable is compatible with ATA66/100/133). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is com patible with ATA33). (Default Value) Set IDE2 Conductor Cable to ATA66/100/133 (Please m ake sure your IDE device and cable is compatible with ATA66/100/133). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is com patible with ATA33). IDE2 Conductor Cable Auto ATA66/100/133 ATA33 On-Chip Primary PCI IDE Enabled Disabled Enabled Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. [. . . ] If not, please double click the CD-ROM device icon in "My com puter", and execute the setup. exe. INSTALL CHIPSET DRIVER This page shows the drivers that need to be installed for the system . Click each item to install the driver manually or switch to the to install the drivers automatically. Massage: Some device drivers will restart your system autom atically. After restarting your system the "Xpress Install" will continue to install other drivers. The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the drivers you want then click the "GO" button. [. . . ]