User manual GIGABYTE BLUE EYE

[. . . ] Before refilling the tank with coolant for testing the Liquid cooling system, please make sure again that all water tube joints are securely fitted and the clips are correctively positioned. While removing water tubes for uninstallation, be sure to keep the device for removal of these tubes away from any electronic part. The following are not covered by the warranty: 1. Use the product incorrectly or in a manner other than the designed purpose. [. . . ] Blue LED with UV inductive current meter to display current status directly. Support the performance required by high-end VGAs. Large water block with pure cooper base (specially water routing designed) All-purpose design, supporting most of water-cooling systems on the market. (1/4", 3/8", and 1/2" tubing) Skid-proof and easy-to-install tube clamps Hair-lined finished aluminum plate Please refer to the English version for all pictures. 4 Component List English (1) 1/4" tube x 1 (2) RAM heatsinks x 16 (3) 1/2" tube clamps x 4 (4) 3/8" tube clamps x 4 GH-WPBV1 VGA Water Block (5) 1/4" tube clamps x 10 (6) 1/2" tube splitters x 2 (7) 3/8" tube splitters x 2 (8) 1/4" tube splitters x 2 (9) Screws x 4 (10) Spring loaded screws x 4 (11) Hold-down plates (12) Base plate (13) Washers x 4 (14) Wrench (15) Grease (16) User manual 5 English I. Hardware Installation 1-1 VGA Fan Disassembly Please disassemble the fan on the VGA Card on your own. 1-2 Hold-Down Plates Introduction There are three combinations for the hold-down plate installations. Type A (Factory Default) Type B Type A supports the following VGA Cards. PCIE nVIDIA ATI 7900 X1900 7800 X1800 6800 AGP nVIDIA ATI 6800 Type B supports the following VGA Cards. PCIE nVIDIA ATI 7300 X850 6200 X700 5750 X600 AGP nVIDIA ATI 1600 X800 X700 9800 9600 6 Type C Take Type B for example. a, place the disc hold-down plate with the engraved Gigabyte logo facing up, so that the mounting holes on the disc hold-down plate match with the mounting holes on the base plate, and secure it with a fastener (as shown in Fig. a). English Type C supports the following VGA Cards. PCIE nVIDIA ATI 7600 1600 6600 1300 6200 AGP nVIDIA ATI 1300 Fig. a Mounting holes on the base plate 1-3 Hold-Down Plates Installation Please decide the type (Type A, Type B, or Type C) of hold-down plate for your VGA Card, depending on the position of the mounting holes. Secure the disc hold-down plate by tightening the screws (Component 9) with the wrench (Component 14) as shown in Fig. b 7 English 1-4 Water Block and VGA Card Installation Apply the grease on the VGA chipset as shown in Fig. c. Place the base plate (Component 12) in the desired position as shown in Fig. f. Insert the screws on the water block into the mounting holes as shown in Fig. f Bolt the base plate using the supplied spring loaded screws (Component 10) as shown in Fig. e, determine the position of the base plate (Component 12) so that its mounting holes line up with the mounting holes on the VGA radiator. Place the washers (Component 13) on the lined up mounting holes, as shown in Fig. e 8 To avoid damage on the chipset, due to over pressure while securing the spring loaded screws, please fasten the screws diagonally. II. [. . . ] Procedure 2: Connect with the 1/2" tube splitter. English Water Pump Tube Procedure 3: Connect the tubes to the water block outlet. Tube Procedure 3: Connect the tubes to the water block inlet. VGA Water Block 1/2" tube 1/4" tube If the CPU water-cooling systems from other brands are used, please follow the size regulation for the water tubes for installation. Before filling the coolant, please make sure that all the tube clamps are secured firmly. 9 English 2-2 Water Tube Installation for Dual VGA Card Procedure 1 and 2: Same as in the water tube installation for single VGA card. Procedure 3: Connect one end of the supplied 1/4" water tube (Component 1) to the supplied 1/2" splitter (Component 8) and the other end to the VGA water block 1 inlet. [. . . ]