User manual GIGABYTE GA-6BXC

[. . . ] System power on by PS/2 Mouse: First, enable this function in CMOS Setup, then you can power on the system by double clicking the right or left button of your PS/2 Mouse. System power on by Keyboard: If your ATX power supply supports larger than 300 mA 5V Stand-By current (dependent on the specification of keyboards), you can power on your system by entering password from the keyboard after setting the "Keyboard power on" password in CMOS Setup. (on JP7) (The ATX power supply supports larger than 720 mA 5V Stand-By current) 2. 3. 5. For Intel Pentium® II / III / CeleronTM Processor MAINBOARD REV. [. . . ] IDE HDD AUTO DETECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TRIONES Bus Master IDE Driver 3. 70 Processor Winbench98 CPU mark32 FPU Winmark Business Disk Hi-End Disk Business Graphics Hi-End Graphics 864 1720 1850 4590 185 207 33. 3 36. 9 1-2 Intel Pentium® II 333MHz(66x5) 350MHz(100x3. 5) 947 1810 1900 4690 204 232 34. 6 39. 2 Winstone98 Business Hi-End Introduction 1. 4. BLOCK DIAGRAM SLOT 1 14. 318MHz 3. 3V SDRAM DIMM Sockets Host Bus 66 / 66 / 100 MHz 100 MHz 33MHz 66 / 100 MHz AGP Bus AGP 66MHz INTEL 82443BX CHIPSET Ultra DMA/33 IDE Ports PCI Bus 33 MHz ICS 9148-26 33 MHz 48MHz 14. 318MHz 24MHz IDE Bus PIIX4 82371EB CHIPSET USB Bus ISA Bus 14. 318MHz COM Ports I/O CHIPSET ITE 8671 LPT Port Floppy Port Keyboard PS/2 Mouse 1-3 6BXC 1. 5. INTRODUCE THE Pentium® II / III Processor Figure 1: Universal Retention Mechanism & attach Mount Figure 2:OEM Pentium® II Processor 1-4 Introduction Figure 3: OEM Pentium® III Processor 1. 6 What is AGP? The Accelerated Graphics Port (AGP) is a new port on the Host-To-PCI bridge device that supports an AGP port. The main purpose of the AGP port is to provide fast access to system memory. The AGP port can be used either as fast PCI port (32-bits at 66MHz vs. 32-Bits at 33MHz) or as an AGP port which supports 2x data-rate, a read queue, and side band addressing. When the 2x-data rate is used the port can transmit data at 533MB/sec (66. 6*2*4). The read-queue can be used to pipeline reads ­ removing the effects of the reads-latency. Side band addressing can be used to transmit the data address on a separate line in order to speed up the transaction. 1-5 6BXC 2. SPECIFICATION 2. 1. HARDWARE · CPU - Pentium® II/ III/ CeleronTM processor 233 ­ 633 MHz. - 242 pins 66 / 100MHz slot1 on board. · SPEED - 66/100 MHz system speed. (2X mode 133MHz) - 33 MHz PCI-Bus speed. - 8 MHz AT bus speed. · DRAM MEMORY - 3 banks 168 pins DIMM module sockets on board. - Use 16 / 32 / 64 / 128 / 256 MB DIMM module DRAM. - 16 ~ 768MB SDRAM. - Supports ECC or Non-ECC type DRAM. · CACHE MEMORY - 32 KB L1 cache memory included in CPU. - 128KB / 512 KB L2 cache memory included in CPU. - Supports DIB speed mode for L2 Cache. · I/O BUS SLOTS - 4 33MHz Master / Slave PCI-BUS. - 1 66MHz / 133MHz AGP bus. · IDE PORTS - 2 Ultra DMA/33 Bus Master IDE channels onboard. (Using IRQ14, 15) - Support Mode 3, 4 IDE & ATAPI CD ­ ROM. · I/O PORTS - Supports 2 16550 COM ports. - Supports 1 1. 44 / 2. 88 MB Floppy port. - Supports PS/2 Mouse & PS/2 Keyboard. 2-1 Specification - Suspend mode support. - Monitor all IRQ / DMA / Display / I/O events. · GREEN FUNCTION · BIOS · DIMENSION 2. 2. SOFTWARE · DRIVER - 2M bits FLASH RAM. - Supports Plug & Play, DMI Function. [. . . ] The RTC is a REALTIME CLOCK device, which provides the DATE & TIME to system. The CMOS SRAM is used for keeping the information of system configuration, so the system can automatically boot OS every time. Since the lifetime of internal battery is 5 years, the user can change a new Battery to replace old one after it cannot work. M Danger of explosion if battery is incorrectly replaced. [. . . ]