User manual GIGABYTE GA-6GXU

[. . . ] PREFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . KEY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PERFORMANCE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BLOCK DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] - Monitor all IRQ / DMA / Display / I/O events. · BIOS · DIMENSION 2. 2. SOFTWARE · DRIVER - Dual FLASH ROM. (DIP 2M & PLCC 2M) - Supports Plug & Play, DMI Function. - ATX Form Factor, 4 layers PCB. - Intel LDCM® (optional. ) - Health monitor Utility. - Adaptec SCSI Driver. · BIOS - Licensed AWARD BIOS. - AT CMOS Setup, BIOS / Chipset Setup, Green Setup, Hard Disk Utility included. · O. S. - Monitor Health status. - Operation with MS-DOS®, Windows®95, Windows®98, WINDOWSTM NT, OS/2, NOVELL and SCO UNIX. 2. 3. · Altitude - 0 to 10, 000 feet (Operating). 2-2 6GXU · Vibration · Electricity - 0 to 1, 000 Hz. 20A current at 5V. ) 2-3 6GXU 3. HARDWARE INSTALLATION 3. 1. UNPACKING The mainboard package should contain the following: · The 6GXU mainboard. · The Retention Mechanism & Attach Mount · USER'S MANUALS for mainboard & SCSI device. · Cable set for IDE, Floppy, SCSI & I/O devices. · Diskettes and CD for Mainboard Utility. · External LVD port adapter. The mainboard contains sensitive electric components, which can be easily damaged by static electricity, so the mainboard should be left in its original packing until it is installed. Unpacking and installation should be done on a grounded anti-static mat. The operator should be wearing an anti static wristband, grounded at the same point as the anti-static mat. Inspect the mainboard carton for obvious damage. Shipping and handling may cause damage to your board. Be sure there are no shipping and handling damages on the board before proceeding. After opening the mainboard carton, extract the system board and place it only on a grounded anti-static surface component side up. Press down on all of the socket IC's to make sure that they are properly seated. Do this only on with the board placed on a firm flat surface. M DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED. 3-1 Hardware Installation 3. 2. MAINBOARD LAYOUT Main BIOS Backup BIOS RING PWR ON POW FAN CPU FAN COMA LPT COMB USB PS/2 JP2 BANK 0 BANK 3 BANK 1 JP3 WAKE ON LAN ISA 2 BZ 1 JP16 JP17 IR PCI 3 PCI 2 PCI 1 SW Adaptec AIC-7890 3. 3. [. . . ] SCSI port Terminator ON 16 bit SCSI DEVICE 16 bit SCSI DEVICE To boot from EXT. SCSI device, please press <Ctrl> <A> for SCSISelect Utility and set the Advanced configuration option/ Support Removable Disks Under BIOS as Fixed Disks to " All Disks". SE Mainboard 14 Terminator ON Terminator OFF Terminator ON 3-12 6GXU CASE 2: Single Ended Termination : High Byte LVD Terminator Control : Enabled 1 LVD SCSI DEVICE LVD SCSI DEVICE LVD Mainboard 8 LVD Terminator ON System has 16 bit & 8 bit SCSI device 16 bit SCSI DEVICE 16 bit SCSI DEVICE SE 8 bit SCSI DEVICE 8 bit SCSI DEVICE LVD Terminator ON Mainboard 4 Terminator ON Terminator OFF High byte Terminator ON Terminator OFF 3 Terminator ON 2 LVD SCSI DEVICE LVD SCSI DEVICE LVD Mainboard 8 LVD Terminator ON System has 8 bit EXT. 50pin SCSI port 16 bit SCSI DEVICE SE 16 bit SCSI DEVICE LVD Terminator ON EXT. 8 bit SCSI DEVICE Terminator ON Mainboard 6 High byte Terminator ON Terminator OFF Terminator ON 3-13 Hardware Installation 3 System has EXT. LVD DEVICE Terminator ON Mainboard EXT. [. . . ]