User manual GIGABYTE GA-6LISL

[. . . ] 1001 LGA1150 socket motherboard for Intel® E3 series processors Copyright © 2013 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations:  For detailed product information, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Table of Contents Box Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 GA-6LISL Motherboard Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GA-6LISL Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 1 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1-1 1-2 1-3 Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Indicates the maximum speed that the SATA controller can support. Options available: Default/Gen1/Gen2/Gen3. Press [Enter] for configuration of advanced items. SATA Mode Selection SATA Test Mode Aggressive LPM Support SATA Controller Speed Software Feature Mask Configuration Serial Port 0/1/2/3/4/5 Port 0/1/2/3/4/5 The category identifies Serial ATA type of hard disk that are installed in the computer. System will automatically detect HDD type. Enable/Disable Port 0/1/2/3/4/5. Enable/Disable Hot Plug support for Serial ATA Port 0/1/2/3/4/5. Enable/Disable External SATA support for Serial ATA Port 0/1/2/3/4/5. Define the SATA Device for Serial ATA Port 0/1. Options available: Hard Disk Drive/Solid State Drive. On an edge detect from 0 to 1, the PCH starts a COMreset initialization to the device. Default setting is Disabled. Hot Plug (for Serial SATA Port 0/1/2/3/4/5) External SATA (for Serial SATA Port 0/1/2/3/4/5) SATA Device Type (for Serial SATA Port 0/1) Spin Up Device (for Serial SATA Port 0/1/2/3/4/5) - 48 - BIOS Setup 2-2-5-1 Software Feature Mask Configuration RAID 0 Enable/Disable RAID 0 feature. Enable/Disable the Intel Rapid Start Technology (IRSTe) funciton. The IRSTe enables your system to get up and running faster from even the deepest sleep, saving time and power consumption. Enable/Disable OROM UI and BANNER feature. When this item is enabled, the HDD password unlock in the OS is enabled. - 49 - RAID 1 RAID 10 RAID 5 Intel Rapid Recovery Technology OROM UI and BANNER HDD Unlock BIOS Setup LED Locate When this item is enabled, the LED/SGPIO hardware is attached and ping to locate feature is enabled on the OS. When this item is enabled, only IRRT volumes can span internal and eSATA drives. If disabled, then any RAID volue can span internal and eSATA drives Options available: Enabled/Disabled. Enable/Disable Intel Smart Response Technlogy. Options available: 2 Seconds/4 Seconds/6 Seconds/8 Seconds. Default setting is 2 Seconds. IRRT Only on eSATA Smart Response Technlogy OROM UI Delay - 50 - BIOS Setup 2-2-6 Info Report Configuration Info Report Configuration Post Report Enable/Disable Post Report support. Default setting is Enabled. Delay Time Options available: 0/1/2/3/4/5/6/78/9/10/Util Press ESC. Default setting isUntil Press ESC. Error Message Report Info Error Message Enable/Disable Info Error Message support. [. . . ] If you are using low-speed memory chips or other kinds of low-performance components and you choose to load these settings, the system might not function properly. Press Enter to configure the device as the boot-up drive. UEFI: Built-in in EFI Shell Press <Enter> on this item to Launch EFI Shell from filesystem device. - 92 - BIOS Setup 2-9 BIOS Beep Codes # of Beeps 1 2 4 4 5 6 Description Invalid password Recovery started S3 Resume failed DXEIPL was not found No Console Input/Output Devices are found Flash update is failed BIOS Setup - 93 - 2-10 BIOS Recovery Instruction The system has an embedded recovery technique. [. . . ]