User manual GIGABYTE GA-6LXSG

[. . . ] If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. Address: 18305 Valley Blvd. , Suite#A LA Puent, CA 91744 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Mother Board Model Number: GA-6LXSG Conforms to the following specifications: FCC Part 15, Subpart B, Section 15. 107(a) and Section 15. 109(a), Class B Digital Device Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful and (2) this device must accept any inference received, including that may cause undesired operation. ERIC LU Representative Person's Name: Signature: Date: Feb. [. . . ] Press "Settings" item and then select the "Output Mode" item. 48 6CX7 Series Motherboard e. Click "Digital" item, Line Out will be change to SPDIF Out. f. Recommend you to select "Autosense", it will auto detect the audio jack you plug in to Line Out is mono or stereo, and then change to SPDIF Out or Speaker out automatically. 49 Memory Installation Memory Installation The motherboard has Rambus In-line Memory Module (RIMM) sockets. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the RIMM Slot . The RIMM module can only fit in one direction due to the two notch. Install memory in any combination table: RIMM 1 RIMM RIMM CRIMM RIMM 2 CRIMM RIMM RIMM 50 6CX7 Series Motherboard Introduce RIMM (Rambus In-line Memory Module) Direct Rambus Memory Controller Directly support a single Direct Rambus * Channel Y Supports 300&400 / 356&400 MHz Direct Rambus * Channel @ 100/133MHz host bus frequency. Y Maximum memory array size up to 256MB using 64Mb/72Mb, 512MB using 128Mb/144Mb, 1GB using 256Mb/288Mb DRAM technology Supports up to 32 Direct Rambus devices per channel Supports a maximum DRAM address decode space of 4GB Configurable optional ECC operation Y ECC with single bit Error Correction and multiple bit Error Detection Y Single bit errors corrected and written back to memory (auto-scrubbing) Y Parity mode not supported DRAM Interface The MCH supports a single channel of Direct RDRAM memory using RSL technology. 300 and 400MHz Direct RDRAM devices are supported. 64, 128 and 256Mb technology Direct RDRAM devices are supported. A maximum of 32 Direct RDRAM devices (64Mb technology = 256MB max) are supported for a single channel. The following table shows the maximum DRAM array size and the minimum increment size for the various DRAM densities supported for MCH. All Rights Reserved Date (mm/dd/yyyy) : Tue Jan 18, 2000 Time (hh/mm/ss) : 14:44:35 TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Pri Master Auto Pri Slave Auto Sec Master Auto Sec Slave Auto Floppy Drive A : 1. 44 MB 3½ Floppy Drive B : Not Installed Boot Sector Virus Protection : Disabled Month : Jan ­ Dec Day : 01­ 31 Year : 1990 ­ 2099 Base Memory : 640 Kb Other Memory : 384 Kb Extended Memory : 127 Mb Total Memory : 128Mb ESC : Exit : Select Item PU / PD / + / ­ :Modify (Shift) F2 : Color Figure 2: Standard CMOS Setup · Date The date format is <Week> <Month> <Day>, <Year>. Week Month Day Year The week, from Sun to Sat, determined by the BIOS and is display-only The month, Jan. The day, from 1 to 31 (or the maximum allowed in the month) The year, from 1990 through 2099 · Time The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. is 13:00:00. 57 BIOS Setup · Primary Master, Slave / Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the computer. There are two types: auto type, and user definable type. User type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If you select User Type, related information will be asked to enter to the following items. Enter the information directly from the keyboard and press <Enter>. [. . . ] Type the password again and press <Enter>. To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. [. . . ]