User manual GIGABYTE GA-6OMM7E

[. . . ] FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] (Default value) Disabled 49 BIOS Setup · BIOS Flash Protection Enabled Disabled Enabled BIOS Flash Protection. (Default Value) · First / Second / Third Boot device Floppy LS120 ZIP100 HDD-0~3 SCSI CDROM Disable LAN Select your boot device priority by Floppy. Select your boot device priority by LS120. Select your boot device priority by ZIP100. Select your boot device priority by HDD-0~3. Select your boot device priority by SCSI. Select your boot device priority by CDROM. Select your boot device priority by LAN. · Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks 720 K, 1. 2 M and 1. 44 M are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1. 2 M or 1. 44 M drive type as they are all 80 tracks. (Default value) BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. Disabled · Boot Up NumLock Status On Off Keypad is number keys. (Default value) Keypad is arrow keys. · Security Option This category allows you to limit access to the system and Setup, or just to Setup. System Setup The system can not boot and can not access to Setup page will be denied if the correct password is not entered at the prompt. The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. (Default value) 50 6OMM7E Motherboard · HDD S. M. A. R. T. Capability Enabled Disabled Enabled HDD S. M. A. R. T. (Default value) · Report No FDD For WIN 95 No Yes Assign IRQ6 For FDD. (Default value) FDD Detect IRQ6 Automatically. 51 BIOS Setup Advanced Chipset Features CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software Advanced Chipset Features Top Performance Disabled Item Help SDRAM Timing Control Auto SDRAM CAS Latency Time 3 Menu Level SDRAM Cycle Time Tras/Trc 6/8 SDRAM RAS-to-CAS Delay 3 SDRAM RAS Precharge Time 3 Delayed Transaction Enabled On-Chip Video Window Size 64MB AGP Graphics Aperture Size 64MB Display Cache Frequency 133MHz System Memory Frequency Auto Onboard Display Cache Setting Initial Display Cache Display Cache Timing Enabled Auto :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Advanced Chipset Features These four items will be available when "SDRAM Timing Control" is set to Manual. This item will be shown when the system bus frequency is 133MHz. These two items will only be shown when you install GA-AIMM card. · Top Performance If you wish to maximize the performance of your system, set "Top Performance" as "Enabled". [. . . ] A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. If you select "System" at "Security Option" in BIOS Features Setup Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu. If you select "Setup" at "Security Option" in BIOS Features Setup Menu, you will be prompted only when you try to enter Setup. 72 6OMM7E Motherboard Save & Exit Setup CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password SAVE to EXIT Exit Setup PnP/PCI Configurations CMOS andSave & (Y/N)? [. . . ]