User manual GIGABYTE GA-6PMM

[. . . ] FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device , pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS INTEGRATED PERIPHERALS HARDWARE MONITOR SETUP SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP EXIT WITHOUT SAVING ESC : Quit (Shift) F2 : Change Color F5 : Old Values : Select Item F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Time, Date, Hard Disk Type, . . . Figure 1: Main Menu · Standard CMOS Setup This setup page includes all the adjustable items in standard compatible BIOS. · BIOS Features Setup This setup page includes all the adjustable items of Award special enhanced features. · Chipset Features Setup This setup page includes all the adjustable items of chipset special features. 48 6PMM Series Motherboard · Power Management Setup This setup page includes all the adjustable items of Green function features. · PnP/PCI Configurations · Load BIOS Defaults This setup page includes all the adjustable configurations of PCI & PnP ISA resources. Load BIOS Defaults option loads preset system parameter values to set the system in its most stable configurations. · Load Setup Defaults Load Setup Defaults option loads preset system parameter values to set the system in its highest performance configurations. · Integrated Peripherals · Hardware Monitor Setup This setup page includes all onboard peripherals. This setup page is auto detect fan and temperature status. · Set Supervisor Password Set Change or disable password. It allows you to limit access to the system and/or BIOS setup. · Set User Password · IDE HDD auto detection · Save & Exit Setup Save CMOS value settings to CMOS and exit setup. It allows you to limit access to the system. Automatically configure hard disk parameters. · Exit Without Saving Abandon all CMOS value changes and exit setup. 49 BIOS Setup Standard CMOS Setup The items in Standard CMOS Features Menu (Figure 2) are divided into 9 categories. Each category includes none, one or more than one setup items. Use the arrows to highlight the item and then use the <PgUp> or <PgDn> keys to select the value in each item. AMIBIOS SETUP ­ STANDARD CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yyyy) : Tue Jan 25, 2000 Time (hh/mm/ss) : 10:36:24 TYPE SIZE CYLS HEAD Pri Master Pri Slave Sec Master Sec Slave : : : : Auto Auto Auto Auto Base Memory : 640 Kb Other Memory: 384 Kb Extended Memory: 30Mb Total Memory: 31Mb ESC : Exit : Select Item PU/PD/+/­ : Modify (Shift)F2 : Color PRECOMP LANDZ SECTOR MODE Floppy Drive A: 1. 44 MB 3 ½ Floppy Drive B: Not Installed Boot Sector Virus Protection : Disabled Month: Jan ­ Dec Day: 01 ­ 31 Year : 1990­ 2099 Figure 2: Standard CMOS Setup · Date The date format is <Week>, <Month>, <Day>, <Year>. Week Month Day Year The week, from Sun to Sat, determined by the BIOS and is display-only The month, Jan. The day, from 1 to 31 (or the maximum allowed in the month) The year, from 1990 through 2099 · Time The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. is 13:00:00. 50 6PMM Series Motherboard · IDE Primary Master / Slave , Secondary Master / Slave The category identifies the type of hard disk from drive C to F that has been installed in the computer. There are two settings: Auto, and Manual. Manual: HDD type is user-definable; Auto will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If you select User Type, related information will be asked to enter to the following items. Enter the information directly from the keyboard and press <Enter>. Such information should be provided in the documentation form your hard disk vendor or the system manufacturer. Number of cylinders HEADS number of heads PRECOMP write precomp LANDZONE Landing zone SECTORS number of sectors If a hard disk has not been installed select NONE and press <Enter>. · Drive A type / Drive B type The category identifies the type of floppy disk drive A or drive B that has been installed in the computer. No floppy drive installed 5. 25 inch PC-type standard drive; 360K byte capacity. [. . . ] It can help you check out which kind of motherboard and which brand of Flash ROM are supported. In method I, if it shows two or more motherboard's model names to be selected, please make sure your motherboard's model name again. Sellecting name will cause the system unbooted. In method II, be sure that motherboard's model name in BIOS unzip file are the same as your motherboard's. [. . . ]