User manual GIGABYTE GA-78LMT-S2P

[. . . ] The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. [. . . ] Allows you to manually set the frequency for the HT Link between the CPU and chipset. HT Link Frequency Set Memory Clock Determines whether to manually set the memory clock. auto lets BIOS automatically set the memory clock as required. Manual allows the memory clock control item below to be configurable. (Default: Auto) This item is present only when you install a CPU that supports this feature. DRAM Configuration x x x x x x x x x x x x CMOS Setup Utility-Copyright (C) 1984-2011 Award Software DRAM Configuration [Unganged] [Auto] Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto [Enabled] [Enabled] [Skip DQS] [Disabled] +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults SPD -- 9T 9T 9T 24T 5T 90ns -- 10T 5T 33T 4T Auto -6T 6T 6T 15T 4T 90ns -6T 4T 20T 4T Item Help Menu Level  DCTs Mode DDR3 Timing Items 1T/2T Command Timing CAS# latency RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time TwTr Command Delay Trfc0 for DIMM1 Trfc1 for DIMM2 Write Recovery Time Precharge Time Row Cycle Time RAS to RAS Delay Channel Interleaving Bank Interleaving DQS Training Control Memclock tri-stating Enter: Select : Move F5: Previous Values DCTs Mode DDR3 Timing Items Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Unganged Sets memory control mode to two single-channel. - 24 - RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time TwTr Command Delay Trfc0 for DIMM1 BIOS Setup Trfc1 for DIMM2 Write Recovery Time Precharge Time Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory bank interleaving. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) Determines whether to enable memory clock tri-stating in CPU C3 or Alt VID mode. (Default: Disabled) DQS Training Control Memclock tri-stating ******** System Voltage Optimized ******** System Voltage Control DDR3 Voltage Control Determines whether to manually set the system voltages. Auto lets the BIOS automatically set the system voltages as required. manual allows all voltage control items below to be configurable. (Default: Auto) Allows you to set memory voltage. Note: Increasing memory voltage may result in damage to the memory. Allows you to set the North Bridge voltage. Allows you to set the South Bridge voltage. NorthBridge Volt Control SouthBridge Volt Control CPU NB VID Control Allows you to set the CPU North Bridge VID voltage. [. . . ] If you do not input the array name, the default array name will be used. Please press Ctrl-Y key to input the LD Name or press any key to exit. If you do not input any LD name, the default LD name will be used. When the next message appears, press <Ctrl>+<Y> to clear the MBR or press other keys to ignore this option. [. . . ]