User manual GIGABYTE GA-7N400-L

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X. AGP 4X/8X notch Caution: AGP 2X card is not supported by nVIDIA® nForceTM 2 Ultra 400. You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. (Default Value) Using Parallel port as ECP & EPP mode. English ECPMode UseDMA This feature allows you to select Direct Memory Access(DMA) channel if the ECP mode selected. This function will available when "Parallel Port Mode" set at ECP or ECP+EPP. (Default Value) Set ECP Mode Use DMA to 1. Game Port Address Disabled 201 209 Disable this function. (Default Value) Set Game Port Address to 209. Midi Port Address Disabled 330 300 Disable this function. (Default Value) Set Midi Port Address to 300. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) - 53 - BIOS Setup 7n400pro2_1001_b. p65 53 2003/7/4, ¤U¤È 03:29 English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type Soft-Off by PWR-BTTN PME Event Wake Up ModemRingOn S3 Resume by USB Resume by Alarm x Date (of Month) Alarm x Time (hh:mm:ss) Alarm Power On by Mouse Power On by Keyboard x KB Power ON Password AC Back Function [S1(POS)] [Instant-off] [Enabled] [Enabled] [Disabled] [Disabled] Everyday 0:0:0 [Disabled] [Disabled] Enter [Soft-Off] [S3] Set suspend type to Suspend to RAM under ACPI OS Item Help Menu Level u [S1] Set suspend type to Power On Suspend under ACPI OS h i g f : Move Enter:Select +/-/PU/PD: Value F10: Save ESC:Exit F5: Previous Values F6: Fail-Safe Defaults Figure 6: Power Management Setup F1: General Help F7: Optimized Defaults ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Off by Power button Instant-off Delay 4 Sec. Press power button then Power off instantly. (Default value) Press power button 4 sec. Enter suspend if button is pressed less than 4 sec. N400 Pro2 / N400 Series Motherboard - 54 - 7n400pro2_1001_b. p65 54 2003/7/4, ¤U¤È 03:29 PME Event Wake Up Disabled Enabled Disable this function. (Default Value) English ModemRingOn An incoming call via modem can awake the system from any suspend state . Disabled Enabled Disable Modem Ring on function. (Default Value) S3 Resume by USB You can resume the system from USB device. (Default Value) Enable this function. Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. (Default Value) Enable alarm function to POWER ON system. If RTC Alarm Lead To Power On is Enabled. Date (of Month) Alarm : Everyday, 1~31 Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59) Power On By Mouse Disabled Mouse Click Disabled this function. (Default value) Double click on PS/2 mouse left button to power on the system. Power On By Keyboard - 55 - BIOS Setup 7n400pro2_1001_b. p65 55 2003/7/4, ¤U¤È 03:29 English This feature allows you to set the method for powering-on the system. The option "Password" allows you to set up to 5 alphanumeric characters to power-on the system. The option "Keyboard 98" allows you to use the standard keyboard 98 to power on the system. [. . . ] Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SCSI" 2. Advanced BIOS features--> First boot device: "SCSI" Then it depends on the mode(RAID or ATA) that you need to set in RAID/ SCSI BIOS. English - 95 - Appendix 7n400pro2_1002_a. p65 95 2003/7/4, ¤U¤È 03:32 English Troubleshooting If you encounter any trouble during boot up, please follow the troubleshooting procedures. START Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Yes Please make sure motherboard & chassis are not short ? Please isolate the short pin. No Failure has been excluded. Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc) are set properly. No Make sure the jumper setting are correct. Yes Failure has been excluded. Plug the CPU cooling fan power in the CPU fan connector. Plug in the AC power connector. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly? [. . . ]