User manual GIGABYTE GA-7VA

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X(3. 3V) card is not supported by VIA® KT400. You might experience system unable to boot up normally. Please insert an AGP 4X/8X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] If use single color LED, power LED will turn off. If use dual color LED, power LED will turn to another color. FSoft-off by PWRBTN 8Instant-off 8Delay 4 Sec. Press power button then Power off instantly. (Default value) Press power button 4 sec to Power off. Enter suspend if button is pressed less than 4 sec. FAC Back Function 8Memory 8Soft-Off 8Full-On System power on depends on the status before AC lost. (Default value) Always power on the system when AC back. F Keyboard Power On This feature allows you to set the method for powering-on the system. The option "Password" allows you to set up to 8 alphanumeric characters to power-on the system. The option "Keyboard 98" allows you to use the standard keyboard 98 to power on the system. 8Password 8Disabled 8Keyboard 98 GA-7VA Motherboard Enter from 1 to 8 characters to set the Keyboard Power On Password. (Default value) If your keyboard have "POWER Key" button, you can press the key to power on your system. - 42 - FMouse Power On 8Disabled 8Enabled Can't Power on system by Mouse Event. (Default value) Can Power on system by Mouse Event. English FPME Event Wake up M When set at Enabled, any PCI-PM event awakes the system from a PCI-PM controlled state. M This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. 8Disabled 8Enabled Disabled PME Event Wake up function. (Default Value) FModem Ring On/ WakeOnLAN (When AC Back Function is set to [Soft-Off]) M You can enable wake on LAN feature by the "ModemRingOn/WakeOnLAN" or "PME Event Wake up" when the M/B has "WOL" onboard connector. Only enabled the feature by "PME Event Wake up". M An incoming call via modem awakes the system from its soft-off mode. M When set at Enabled, an input signal comes from the other client. Server on the LAN awaks the system from a soft off state if connected over LAN. 8Disabled 8Enabled Disabled Modem Ring On / Wake On LAN function. Enabled Modem Ring On / Wake On LAN function. (Default Value) FResume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. 8Disabled 8Enabled Disable this function. (Default Value) Enable alarm function to POWER ON system. If RTC Alarm Lead To Power On is Enabled. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : Everyday, 1~31 (0~23) : (0~59) : (0~59) - 43 - BIOS Setup English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI1/PCI5 IRQ Assignment PCI2 IRQ Assignment PCI3 IRQ Assignment PCI4 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Levelu higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: PnP/PCI Configurations FPCI1/PCI5 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1/ PCI 5. [. . . ] No Insert and push the memory module vertically into the DIMM slot. Check if the memory install properly into the DIMM slot. Yes Failure has been excluded. Insert the VGA card. Then plug in ATX power cable and turn on the system. A GA-7VA Motherboard - 76 - English A The problem could be caused by power supply, CPU, memory or CPU/memory socket itself. No Is memory LED on and CPU fan running? Yes Failure has been excluded. No Check if there is display. Perhaps your VGA card / VGA slot or monitor is defective. Yes Turn off the system. [. . . ]