User manual GIGABYTE GA-7VM400MF

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X(3. 3V) card is not supported by VIA® KM400. You might experience system unable to boot up normally. Please insert an AGP 4X/8X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port using IRQ7. (Default Value) Using Parallel port as Enhanced Parallel Port IRQ5. Using Parallel port as Extended Capabilities Port using IRQ7. Using Parallel port as ECP & EPP mode. Game Port Address Disabled 201 209 Disable this function. (Default Value) Set Game Port Address to 209. Midi Port Address Disabled 300 330 Disable this function. Set Midi Port Address to 330. (Default Value) Midi Port IRQ 5 10 Set 5 for Midi Port IRQ. (Default value) GA-7VM400M(F) Motherboard - 42 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe [S1(POS)] Item Help xUS D vc WaeUpFo S B e ie k- rm 3 Pow er LED in S1 state Soft-Off by PWRBTN AC Back Function Key board Pow er On Mouse Pow er On PME Ev ent Wake Up ModemRingOn/WakeOnLAN Resume by Alarm x Date(of Month) Alarm x Time(hh:mm:ss) Alarm Dsbe iald [Blinking] [Instant-off] [Soft-Off] [Disabled] [Disabled] [Enabled] [Enabled] [Disabled] Ev ery day 0: 0: 0 MeuLv l n e eu [S1] Set suspend ty pe to Pow er On Suspend under ACPI OS [S3] Set suspend ty pe to Suspend to RAM under ACPI OS higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F5:Prev ious Values F6:Fail-Safe Defaults Figure 5: Pow er Management Setup F1:General Help F7:Optimized Defaults ACPI Suspend Type S1/POS S3/STR Set suspend type to Power On Suspend under ACPI OS (Power On Suspend). (Default value) Set suspend type to Suspend To RAM under ACPI OS (Suspend To RAM). USB Device Wakeup From S3(When ACPI S uspend Type i s set [S 3/S TR]) USB device wakeup From S3 can be set when ACPI standby state set to S3/STR. Enabled Disabled USB Device can wakeup system from S3. USB Device can't wakeup system from S3. (Default value) - 43 - BIOS Setup English Power LED i n S1 state Blinking Dual/OFF In standby mode(S1), power LED will blink. If use single color LED, power LED will turn off. If use dual color LED, power LED will turn to another color. Soft-off by PWRBT N Instant-off Delay 4 Sec. Press power button then Power off instantly. (Default value) Press power button 4 sec to Power off. Enter suspend if button is pressed less than 4 sec. AC Back Function Memory Soft-Off Full-On System power on depends on the status before AC lost. (Default value) Always power on the system when AC back. Keyboard Power On This feature allows you to set the method for powering-on the system. The option "Password" allows you to set up to 8 alphanumeric characters to power-on the system. The option "Keyboard 98" allows you to use the standard keyboard 98 to power on the system. Password Disabled Keyboard 98 Enter from 1 to 8 characters to set the Keyboard Power On Password. (Default value) If your keyboard have "POWER Key" button, you can press the key to power on your system. Mouse Power On Disabled Enabled Can't Power on system by Mouse Event. (Default value) Can Power on system by Mouse Event. GA-7VM400M(F) Motherboard - 44 - PME Event Wake up M When set at Enabled, any PCI-PM event awakes the system from a PCI-PM controlled state. [. . . ] No Plug the CPU cooling fan power in the CPU fan connector. Plug in the AC power connector. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly?No Insert and push the memory module vertically into the DIMM slot. Check if the memory install properly into the DIMM slot. [. . . ]