User manual GIGABYTE GA-8GE800 PRO

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Select y our boot dev ice priority by USB-CDROM. Select y our boot dev ice priority by USB-HDD. Select y our boot dev ice priority by LAN. Select y our boot dev ice priority by Disabled. - 39 - BIOS Setup English C Boot Up Fl oppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks 720 K, 1. 2 M and 1. 44 M are all 80 tracks. 8Enabled BIOS searches for floppy disk driv e to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1. 2 M or 1. 44 M driv e ty pe as they are all 80tracks. 8Disabled BIOS w ill not search for the ty pe of floppy disk driv e by track number. Note that there w ill not be any w arning message if the driv e installed is 360 K. (Default v alue) C Password Check Please refer to the detail on P. 58 8Sy stem 8Setup The sy stem can not boot and can not access to Setup page w ill be denied if the correct passw ord is not entered at the prompt. The sy stem w ill boot, but access to Setup w ill be denied if the correct passw ord is not entered at the prompt. (Default v alue) CCPU Hyper-Threading 8Enabled Enables CPU Hy per Threading Feature. Please note that this feature is only w orking for operating sy stem w ith multi processors mode supported. (Default v alue) 8Disabled Disables CPU Hy per Threading. CInit Display First 8Onboard/AGP 8PCI Set Init Display First to onboard/AGP. (Default v alue) Set Init Display First to PCI. CGraphics Aperture Size 8128MB 8Disabled Set Graphics Aperture Size to 128MB. (Default v alue) Disable this function. CGraphics Share Memory 88MB 81MB Set Graphics Share Memory to 8MB. (Default v alue) Set Graphics Share Memory to 1MB. GA-8GE800 Pro Motherboard - 40 - English Integrated Peripherals CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Integrated Peripherals On-Chip Primary PCI IDE On-Chip Secondary PCI IDE IDE1 Conductor Cable IDE2 Conductor Cable USB Controller USB Key board Support USB Mouse Support AC97 Audio Onboard H/W 1394 Onboard H/W LAN Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode x ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ CIR Port Address x CIR Port IRQ [Enabled] [Enabled] [Auto] [Auto] [Enabled] [Disabled] [Disabled] [Auto] [Enabled] [Enabled] [3F8/IRQ4] [2F8/IRQ3] [Normal] Half [378/IRQ7] [SPP] 3 [201] [330] [10] [Disabled] 11 [Disabled] Disable onboard IDE PORT [Enabled] Enable onboard IDE PORT Item Help Menu Lev el u If a hard disk controller card is used, set at Disable higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F3: Language F5:Prev ious Values F6:Fail-Safe Defaults Figure 4: Integrated Peripherals F1:General Help F7:Optimized Defaults - 41 - BIOS Setup English C On-Chip Primary PCI IDE 8Enabled 8Disabled Enable onboard 1st channel IDE port. (Default v alue) Disable onboard 1st channel IDE port. C On-Chip Secondary PCI IDE 8Enabled 8Disabled Enable onboard 2nd channel IDE port. (Default v alue) Disable onboard 2nd channel IDE port. C IDE1 Conductor Cable 8Auto 8ATA66/100 8ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure y our IDE dev ice and cable is compatible w ith ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE dev ice and cable is compatible w ith ATA33). C IDE2 Conductor Cable 8Auto 8ATA66/100 8ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure y our IDE dev ice and cable is compatible w ith ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE dev ice and cable is compatible w ith ATA33). C USB Controller 8Enabled 8Disabled Enable USB Controller. [. . . ] O. S. /A. S. : Model name Size: Driver/Utility: Company: E-mail Add. : PCB revision: Phone No. : English & & Problem Description: - 101 - Appendix English Troubleshooting If you encounter any trouble during boot up, please follow the troubleshooting procedures . START Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ?No Yes Please isolate the short pin. Failure has been excluded. Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc. ) are set properly. No Make sure the jumper setting are correct. Yes Failure has been excluded. No Plug the CPU cooling fan power in the CPU fan connector. [. . . ]