User manual GIGABYTE GA-8GEMT4

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Enable onboard Serial port 2 and address is 2E8. Disable onboard Serial port 2. C UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) 8ASKIR 8IrDA 8Normal Set onboard I/O chip UART to ASKIR Mode. Set onboard I/O chip UART to Normal Mode. (Default Value) C UR2 Dupl ex Mode 8Half 8Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. C Onboard Parallel port 8378/IRQ7 8278/IRQ5 8Disabled 83BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. - 33 BIOS Setup English CParallel Port Mode 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Ex tended Capabilities Port. Using Parallel port as ECP & EPP mode. CECP Mode Use DMA 83 81 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. CMidi Port Address 8300 8330 8Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. CMidi Port IRQ 85 810 Set Midi Port IRQ to 5. (Default Value) CCIR Port Address 8310 8320 8Disabled Set CIR Port Address to 310. Disable this function. (Default Value) CCIR Port IRQ 85 811 Set CIR Port IRQ to 5. (Default Value) GA-8GEMT4 Series Motherboard - 34 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Soft-Off by PWR_BTTN PME Ev ent Wake Up ModemRingOn/WakeOnLan Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function [S1(POS)] [Instant-Off] [Enabled] [Enabled] [Disabled] Ev ery day 000 [Disabled] [Disabled] Enter [Soft-Off] Item Help Menu Lev el u [S1] Set suspend ty pe to Pow er On Suspend under ACPI OS [S3] Set suspend ty pe to Suspend to RAM under ACPI OS higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F5:Prev ious Values F6:Fail-Safe Defaults Figure 5: Pow er Management Setup F1:General Help F7:Optimized Defaults C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Soft-off by PWR_BTT N 8Instant-off 8Delay 4 Sec. Press pow er button then Pow er off instantly . (Default v alue) Press pow er button 4 sec to Pow er off. Enter suspend if button is pressed less than 4 sec. C PME Event Wake Up 8Disabled 8Enabled Disable this function. [. . . ] Connect co-axial or optical output to the SPDIF decoder. GA-8GEMT4 Series Motherboard - 72 - English - 73 - Technical Reference English GA-8GEMT4 Series Motherboard - 74 - Revision History Chapter 5 Appendix Picture below are shown in Windows XP (CD driver version 1. 0) Appendix A: Chipset Driver Installation A. Intel Chipset Software Installation Utility: Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup. exe. English 1. Click "Intel Chipset Software Installation Utility" item. (1) (2) 3. Click "Yes". 2. Click "Next". (4) (3) - 75 - Appendix English 4Click "Next". (5) (6) 5. Click "Finish" to restart computer. (7) GA-8GEMT4 Series Motherboard - 76 - B. [. . . ]