User manual GIGABYTE GA-8ID

[. . . ] If this Eric Lu equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. Address: 18305 Valley Blvd. , Suite#A LA Puent, CA 91744 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Mother Board Model Number: GA-8ID Conforms to the following specifications: FCC Part 15, Subpart B, Section 15. 107(a) and Section 15. 109(a), Class B Digital Device Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful and (2) this device must accept any inference received, including that may cause undesired operation. ERIC LU Representative Person's Name: Signature: Date: Apr. 12, 2001 -Reorient or relocate the receiving antenna -Move the equipment away from the receiver -Plug the equipment into an outlet on a circuit different from that to which the receiver is connected -Consult the dealer or an experienced radio/television technician for additional suggestions You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void Your authority to operate such equipment. [. . . ] You may also restart by simultaneously pressing <Ctrl> - <Alt>- <Del> keys. CONTROL KEYS <> <> <> <> <Esc> Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Load the default CMOS value from BIOS default table, only for Option Page Setup Menu Load the Setup Defaults Reserved Reserved Save all the CMOS changes, only for Main Menu <+/ PgUp> <-/ PgDn> <F1> <F2> <F3> <F4> <F5> <F6> <F7> <F8> <F9> <F10> 45 BIOS Setup GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. The Main Menu Once you enter AMI BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. The Main Menu allows you to select from nine setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. AMIBIOS SIMPLE SETUP UTILITY ­ VERSION 1. 24d (C) 1999 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP / PCI CONFIGURATION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS INTEGRATED PERIPHERALS HARDWARE MONITOR & MISC SETUP SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP EXIT WITHOUT SAVING ESC: Quit : Select Item (Shift)F2 : Change Color F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults F10:Save & Exit Time, Date , Hard Disk Type. . . Figure 1: Main Menu · Standard CMOS Setup This setup page includes all the adjustable items in standard compatible BIOS. · BIOS Features Setup This setup page includes all the adjustable items of Award special enhanced features. 46 8TM Motherboard · Chipset Features Setup This setup page includes all the adjustable items of chipset special features. · Power Management Setup This setup page includes all the adjustable items of Green function features. · PnP/PCI Configurations This setup page includes all the adjustable configurations of PCI & PnP ISA resources. · Load BIOS Defaults Load BIOS Defaults option loads preset system parameter values to set the system in its most stable configurations. · Load Setup Defaults Load Setup Defaults option loads preset system parameter values to set the system in its highest performance configurations. · Integrated Peripherals This setup page includes all onboard peripherals. · Hardware Monitor & MISC Setup This setup page is auto detect fan and temperature status. · Set Supervisor Password Set Change or disable password. It allows you to limit access to the system and/or BIOS setup. · Set User Password Set Change or disable password. It allows you to limit access to the system. · IDE HDD auto detection Automatically configure hard disk parameters. · Save & Exit Setup Save CMOS value settings to CMOS and exit setup. · Exit Without Saving Abandon all CMOS value changes and exit setup. 47 BIOS Setup Standard CMOS Setup The items in Standard CMOS Setup Menu (Figure 2) are divided into 10 categories. Each category includes none, one or more than one setup items. Use the arrows to highlight the item and then use the <PgUp> or <PgDn> keys to select the value in each item. AMIBIOS SETUP ­ STANDARD CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yyyy) : Fri Mar 16, 2001 Time (hh/mm/ss) : 14:44:35 Pri Master Pri Slave Sec Master Sec Slave : : : : TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Auto Auto Auto Auto Floppy Drive A : 1. 44 MB 3½ Floppy Drive B : Not Installed Boot Sector Virus Protection : Disabled Month : Jan ­ Dec Day : 01­ 31 Year : 1990 ­ 2099 Base Memory : 640 Kb Other Memory : 384 Kb Extended Memory : 255 Mb Total Memory : 256 Mb ESC : Exit : Select Item PU / PD / + / ­ :Modify (Shift) F2 : Color Figure 2: Standard CMOS Setup · Date The date format is <Week>, <Month> <Day> <Year>. Week Month Day Year The week, from Sun to Sat, determined by the BIOS and is display-only The month, Jan. Most use for this area is Shadow RAM. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map. 50 8TM Motherboard BIOS Features Setup AMIBIOS SETUP ­ BIOS FEATURES SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved 1st Boot Device : Floppy 2nd Boot Device : IDE-0 3rd Boot Device : CDROM Floppy Drive Seek : Disabled BootUp Num-Lock : On Password Check : Setup S. M. A. R. T. for Hard Disks : Disabled ESC: Quit : Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values(Shift)F2:Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Figure 3: BIOS Features Setup · 1st / 2nd / 3rd Boot Device Floppy ZIP A:/LS-120 CDROM SCSI NETWORK IDE-0~IDE-3 Disabled ATAPI ZIP C: Set your boot device priority to Floppy. Set your boot device priority to ZIP A:/LS-120. Set your boot device priority to NETWORK. Set your boot device priority to IDE-0~IDE-3. Set your boot device priority to ATAPI ZIP C:. · Floppy Drive Seek During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360 type is 40 tracks while 720, 1. 2 and 1. 44 are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks. Note that BIOS can't differentiate between from 720, 1. 2 or 1. 44 drive type as they are all 80 tracks. [. . . ] Complete update process following the instruction. Save BIOS In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the current BIOS version. Check out supported motherboard and Flash ROM : In the very beginning, there is "About this program" icon shown in dialog box. [. . . ]