User manual GIGABYTE GA-8IEML-T

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Do not use AGP 2X card (3. 3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845(E/G) / 850(E) chipset can't support AGP 2X(3. 3V). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/ 4X mode AGP slot. [. . . ] Set RxD, TxD Active to Lo, Lo. IR Transmission Delay Enabled Disabled Enable IR Transmission delay. (Default Value) Disable IR Transmission delay. UR2 Duplex Mode Half Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. Use IR Pins IR-Rx2xTx2 RxD2, TxD2 Set IR Pins use IR-Rx2xTx2. (Default Value) Set IR Pins use RxD2, TxD2. Onboard Parallel port 378/IRQ7 278/IRQ5 Disabled 3BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. 34 BIOS Setup Parallel Port Mode SPP EPP ECP ECP+EPP Normal Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as ECP & EPP mode. Normal Operation. EPP Mode Select EPP1. 7 EPP1. 9 Set EPP Mode Select to EPP1. 7. (Default Value) Set EPP Mode Select to EPP1. 9. ECP Mode Use DMA 3 1 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. Game Port Address 201 209 Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. Midi Port Address 290 300 330 Disabled Set Midi Port Address to 290. Set Midi Port Address to 330. (Default Value) Disable this function. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) 35 GA-8IEML-T Series Motherboard Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Power Management Setup ACPI Suspend Type Power LED in S1 state Soft-Off by PWR_BTTN PME Event Wake Up ModemRingOn Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Mouse Power On Keyboard Power On x KB Power ON Password AC Back Function S1(POS) Blinking Instant-Off Enabled Enabled Disabled Everyday 000 Disabled Disabled Enter Soft Off [S3] Set suspend type to Suspend to RAM under ACPI OS Item Help Menu Level [S1] Set suspend type to Power On Suspend under ACPI OS : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Power Management Setup ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Power LED in S1 state Blinking Dual/Off In standby mode(S1), power LED will blink. If use single color LED, power LED will turn off. If use dual color LED, power LED will turn to another color. 36 BIOS Setup Soft-off by PWR_BTTN Instant-off Press power button then Power off instantly. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up Disabled Enabled Disable this function. (Default Value) ModemRingOn Disabled Enabled Disable Modem Ring on function. (Default Value) Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. [. . . ] Microsoft(R) Windows98 © Copyright Microsoft Corp 1981-1999 A:\> dir/w Volume in drive A has no label Volume Serial Number is 16EB-353D Directory of A:\ COMMAND. COM 7VTX. F4 FLASH841. EXE 3 file(s) 838, 954 bytes 0 dir(s) 324, 608 bytes free A:\> Flash841 7VTX. F4 (2) Now screen appears the following Flash Utility main menu. Press "Enter", the highlighted item will locate on the model name of the right-upper screen. Right after that, press "Enter" to start BIOS Flash Utility. 71 GA-8IEML-T Series Motherboard (3) It will pop up a screen and asks "Are you sure to flash the BIOS?" Press [Enter] to continue the procedure, or press [ESC] to quit. Beware: Please do not turn off the system while you are upgrading BIOS. [. . . ]