User manual GIGABYTE GA-8IG1000-L

[. . . ] It can be switched between AGP 2X (3. 3V) or 4X(1. 5V) mode by adjusting the jumper. The factory default for this card is 2X(3. 3V). If you install this card in GA-8IG1000-L (or any AGP 4X only) motherboards without switching the jumper to 4X mode (1. 5V), it will burn the motherboard. Example 2: ATi Rage 128 Pro (Power Color) & SiS 305 golden finger is compatible with 2X/4X mode AGP slot, but it supports 2X(3. 3V) only. [. . . ] (Default Value) When AC-power back to the system, the system will be in "On" state. When AC-power back to the system, the system will return to the Last state before AC-power off. ModemRingOn/WakeOnLan Disabled Enabled Disable Modem Ring On / Wake On LAN function. The modem ring / LAN wake up will bring the system out of soft-off or suspend state if this option is set "Enabled". (Default Value) 38 BIOS Setup PME Event Wake up Disabled Enabled Disable PME event wake up function. The PME event wake up will bring the system out of soft-off or suspend state if this option is set "Enabled". (Default Value) Resume by RTC Alarm You can set "Resume by RTC Alarm " item to enabled and key in Data/time to power on system. Disabled Enabled Disable this function. (Default Value) Enable alarm function to POWER ON system. If Resume by RTC Alarm is Enabled. RTC Alarm Date: RTC Alarm Hour: RTC Alarm Minute: RTC Alarm Second: Every Day, 1~31 0~23 0~59 0~59 KB & PS/2 Mouse Access Monitor Ignore Monitor Keyboard & PS/2 Mouse Access. (Default Value) Ignore Keyboard & PS/2 Mouse Access. FDC/LPT/COM Ports Access Monitor Ignore Monitor FDC/LPT/COM Ports Access. (Default Value) Ignore FDC/LPT/COM Ports Access. Pri. Master IDE Access Monitor Ignore Monitor Primary Master IDE Access. (Default Value) Ignore Primary Master IDE Access. Pri. All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP INTEGRATED PERIPHERALS HARDWARE MONITOR & MISC SETUP SUPERVISOR PASSWORD USER PASSWORD Load Optimized Defaults?(Y/N)?N DETECTION PNP / PCI CONFIGURATION IDE HDD AUTO LOAD FAIL-SAFE DEFAULTS LOAD OPTIMIZED DEFAULTS ESC: Quit F6: Fail-Safe Values SAVE & EXIT SETUP EXIT WITHOUT SAVING : Select Item F7: Optimized Values F8: Flash Utility F5: Old Values F10:Save & Exit Load Optimized Defaults Figure 8: Load Optimized Defaults Load Optimized Defaults Optimized defaults contain the most appropriate system parameter values to configure the system to achieve maximum performance. 44 BIOS Setup Integrated Peripherals AMIBIOS SETUP - INTEGRATED PERIPHERALS ( C ) 2001 American Megatrends, Inc. All Rights Reserved OnBoard IDE IDE1 Conductor Cable IDE2 Conductor Cable OnBoard FDC OnBoard Serial Port A OnBoard Serial Port B Serial Port B Mode IR Duplex Mode OnBoard CIR Port CIR IRQ Select OnBoard Parallel Port Parallel Port Mode EPP Version Parallel Port IRQ Parallel Port DMA OnBoard Midi Port Midi IRQ Select OnBoard Game Port Mouse PowerOn Function Keyboard PowerOn Function : Both : Auto : Auto : Auto : Auto : Auto : Normal : Half Duplex : Disabled : 10 : Auto : ECP : N/A : Auto : Auto : Disabled : 10 : 200 : Disabled : Disabled ESC: Quit F1 : Help F5 : Old Values F6 : Fail-Safe F7 : Optimized F8: Flash Utility : Select Item PU/PD/+/- : Modify (Shift)F2: Color Specific Key for PowerOn USB Function USB Legacy Support AC97 Audio AC97 Modem : N/A : Enabled : Disabled : Auto : Auto Figure 9: Integrated Peripherals 45 GA-8IG1000-L Motherboard OnBoard IDE Disabled Both Primary Secondary Disable OnBoard IDE. Both Primary & Secondary IDE channel will be enabled. (Default Value) Only Primary IDE channel is enabled. Only Secondary IDE channel is enabled. IDE1 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). IDE2 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). OnBoard FDC Disabled Enabled Auto Disable this function. Set the floppy disk controller automatically. [. . . ] Y LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit F6: Load BIOS Defaults : Select Item SAVE & EXIT SETUP EXIT WITHOUT SAVING (Shift)F2 : Change Color F5: Old Values F7: Load Setup Defaults F10:Save & Exit Save Data to CMOS & Exit SETUP 79 GA-8IG1000-L Motherboard STEP 5: BIOS flashing. (1) After the system boot from floppy disk, type "A:\> dir/w" and press "Enter" to check the entire files in floppy A. Then type the "BIOS flash utility" and "BIOS file" after A:\>. In this case you have to type "A:\> Flash841 7VTX. F4" and then press "Enter". [. . . ]