User manual GIGABYTE GA-8IPE1000MT

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4 X/8 X notc h Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E) /E7205 / 865(P/G/PE) / 875P. You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Disable onboard Serial port 2. UART Mode Select This item allow s y ou to determine w hich Infra Red(IR) function of Onboard I/O chip. Normal IrDA ASKIR SCR Set onboard I/O chip UAR T to Norm al Mode. (Default Value) Set onboard I/O chip UAR T to IrDA Mode. Set onboard I/O chip UART to ASKIR Mode. Set onboard I/O chip U ART to SCR Interface. UR2 Dupl ex Mode This feature allow s y ou to sec lect IR mode. This function w ill av ailable w hen "UART Mode Select" does n't set at Normal/SCR. (Default Value) IR F unction Duplex F ull. Onboard Parallel port This feature allow s y ou to select from a giv en set of parameters if the parallel port uses the onboard I/O controller. Disabled 378/ IRQ7 278/ IRQ5 3BC/ IRQ7 Disable onboard LPT port. Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/ IRQ5. Enable onboard LPT port and address is 3BC/ IRQ7. GA-8IPE1000MT Motherboard - 44 - 8ipe1000mt_1001_b. p65 44 2003/4/15, ¤U¤È 05:15 Parallel Port Mode This feature allow s y ou to connect w ith an adv anc ed printer v ia the port mode it supports. SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Ex tended Capabilities Port. Using Parallel port as ECP & EPP mode. English ECP Mode Use DMA This feature allow s y ou to select Direc t Memory Access (DMA) channel if the ECP mode s elected. This function w ill av ailable w hen "Parallel Port Mode" set at ECP or ECP+EPP. (Default Value) Set ECP Mode Use DMA to 1. Game Port Address 201 209 Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. Midi Port Address 300 330 Disabled Set M idi Port Address to 300. (Default Value) Disable this function. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) - 45 - BIOS Setup 8ipe1000mt_1001_b. p65 45 2003/4/15, ¤U¤È 05:15 English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Pow er LED in S1 state Off by Pow er button PME Ev ent Wak e Up ModemR ingOn/WakeOnLan Resume by Alarm x Date (of Month) Alarm x Time (hh:mm:ss) Alarm Pow er On by M ouse Pow er On by Key board x KB Pow er ON Pas sw ord AC Back Func tion [S1(POS)] [Blinking] [Instant-off] [Enabled] [Enabled] [Disabled] Ev ery day 0:0 :0 [Disabled] [Disabled] Enter [Soft-Off] [S3] Set s uspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] Set s uspend ty pe to Pow er On Suspend under ACPI OS higf: Mov e Enter:Select +/-/PU/ PD:Value F10:Sav e ESC:Ex it F 1:General Help F5:Prev ious Values F6: Fail-Safe Defaults F7:Optimized Defaults Figure 5: Pow er Management Setup ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. Power LED i n S1 state Blinking Dual/OFF In standby mode(S1), pow er LED w ill blink. [. . . ] No Plug the C PU cooling fan power in the CP U fan connector. Plug in the AC pow er connector. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly?No I nsert and push the memory module vertically into the DI MM slot. Check if the memory install properly into the DIMM slot. [. . . ]