User manual GIGABYTE GA-8IR533

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Do not use AGP 2X card (3. 3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845(E/G) / 850(E) chipset can't support AGP 2X(3. 3V). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/ 4X mode AGP slot. [. . . ] Enable onboard Serial port 2 and address is 3F8. Enable onboard Serial port 2 and address is 2F8. (Default v alue) Enable onboard Serial port 2 and address is 3E8. Enable onboard Serial port 2 and address is 2E8. Disable onboard Serial port 2. C UART Mode Select (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) 8ASKIR 8IrDA 8Normal Set onboard I/O chip UART to ASKIR Mode. Set onboard I/O chip UART to Normal Mode. (Default Value) 33 GA-8IR533 Series Motherboard C UR2 Dupl ex Mode 8Half 8Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. C Onboard Parallel port 8378/IRQ7 8278/IRQ5 8Disabled 83BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. CParallel Port Mode 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Ex tended Capabilities Port. Using Parallel port as ECP & EPP mode. CECP Mode Use DMA 83 81 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. CMidi Port Address 8290 8300 8330 8Disabled Set Midi Port Address to 290. Set Midi Port Address to 330. (Default Value) Disable this function. 34 BIOS Setup CCIR Port Address 8310 8320 8Disabled Set CIR Port Address to 310. (Default Value) Set CIR Port Address to 320. Disable this function. CCIR Port IRQ 85 811 Set CIR Port IRQ to 5. (Default Value) 35 GA-8IR533 Series Motherboard Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Pow er LED in S1 state Soft-Off by PWR_BTTN ModemRingOn PME Ev ent Wake Up Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function S1(POS) Blinking Instant-Off Enabled Enabled Disabled Ev ery day 000 Disabled Disabled Enter Soft-Off Set suspend ty pe to Pow er On Suspend under ACPI OS [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Power LED i n S1 state 8Blinking 8Dual/Off In standby mode(S1), pow er LED w ill blink. If use single color LED, pow er LED w ill turn off. [. . . ] Press "Enter", the highlighted item will locate on the model name of the right-upper screen. Right after that, press "Enter" to start BIOS Flash Utility. 69 GA-8IR533 Series Motherboard (3) It will pop up a screen and asks "Are you sure to flash the BIOS?" Press [Enter] to continue the procedure, or press [ESC] to quit. Beware: Please do not turn off the system while you are upgrading BIOS. It will render your BIOS corrupted and system totally inoperative. Are you sure to flash the BIOS? [. . . ]