User manual GIGABYTE GA-8PEMT4

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X(1. 5V). Caution: AGP 2X(3. 3V) card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). You might experience system unable to boot up normally. Please insert an AGP 4X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Set onboard I/O chip UART to Normal Mode. (Default Value) C UR2 Dupl ex Mode 8Half 8Full IR Function Duplex Half. (Default Value) IR Function Duplex Full. C Onboard Parallel port 8378/IRQ7 8278/IRQ5 8Disabled 83BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. CParallel Port Mode 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Ex tended Capabilities Port. Using Parallel port as ECP & EPP mode. - 33 BIOS Setup English CECP Mode Use DMA 83 81 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. CMidi Port Address 8300 8330 8Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. CMidi Port IRQ 85 810 Set Midi Port IRQ to 5. (Default Value) FCIR Port Address This feature allow s y ou to select CIR port address or disable it. 8Disabled 8310 8320 Disabled this function. (Default Value) Enabled CIR and Address is 310. Enabled CIR and Address is 320. FCIR Port IRQ (When Parallel Port Mode is set [ECP or ECP+EPP]) This feature allows you to select CIR IRQ , if CIR is enabled. 85 811 CIR use IRQ 5. (Default Value) GA-8PEMT4 Series Motherboard - 34 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Soft-Off by PWR_BTTN PME Ev ent Wake Up ModemRingOn/WakeOnLan Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Alarm Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function S1(POS) Instant-Off Enabled Enabled Disabled Ev ery day 000 Disabled Disabled Enter Soft-Off [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Set suspend ty pe to Pow er On Suspend under ACPI OS Item Help Menu Lev el u [S1] higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F5:Prev ious Values F6:Fail-Safe Defaults F1:General Help F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type This option will not be shown or not be available if you are using a CPU with the locked ratio. 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Soft-off by PWR_BTT N 8Instant-off 8Delay 4 Sec. Press pow er button then Pow er off instantly . (Default v alue) Press pow er button 4 sec to Pow er off. Enter suspend if button is pressed less than 4 sec. C PME Event Wake Up 8Disabled 8Enabled Disable this function. [. . . ] It is the best solution if y ou need 6 channel output, Line In and MIC at the same tim e. "SURROUND-KIT" is included in the GIGABYTE unique "Audio Combo Kit" as picture. STEP 1 : Insert the "Audio Combo Kit" in the back of the case , and fix it w ith the screw . STEP 2 : Connect the "SURROUND-KIT" to SUR_CEN on the M/B. GA-8PEMT4 Series Motherboard - 70 - STEP 3 : Connect the front channels to back audio panel' s "Line Out", the rear channels to SURROUND-KIT' s REAR R/L, and the Center/Subw oofer channels to SURROUND-KIT ' SUB CENTER. s English STEP 4 : Click the audio icon "Sound Effect" from the w indow s tray at the bottom of the screen. STEP 5 : Select "Speaker Configuration", and choos e the "6 channels for 5. 1 speakers out put". Enable "Only SURROUND-KIT" and press "OK". Basic & Advanced 6 Channel Analog Audio Output ModeNotes: When the "Env ironment settings" is "None", the sound w ould be performed as stereo mode(2 channels output). [. . . ]