User manual GIGABYTE GA-8SQ800 ULTRA2

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual GIGABYTE GA-8SQ800 ULTRA2. We hope that this GIGABYTE GA-8SQ800 ULTRA2 user guide will be useful to you.

Lastmanuals help download the user guide GIGABYTE GA-8SQ800 ULTRA2.


Mode d'emploi GIGABYTE GA-8SQ800 ULTRA2
Download

You may also download the following manuals related to this product:

   GIGABYTE GA-8SQ800 ULTRA2 annexe 4 (5531 ko)
   GIGABYTE GA-8SQ800 ULTRA2 ANNEXE 2 (406 ko)
   GIGABYTE GA-8SQ800 ULTRA2 annexe 1 (1549 ko)
   GIGABYTE GA-8SQ800 ULTRA2 annexe 3 (855 ko)

Manual abstract: user guide GIGABYTE GA-8SQ800 ULTRA2

Detailed instructions for use are in the User's Guide.

[. . . ] (d) Driver CD for your motherboard. (1) Installing IDE hard drive(s) in your system Attach one end of the IDE cable to the rear of the IDE hard drive and the other end to IDE port(s) controlled by the GigaRAID controller on the motherboard. (To ensure that your IDE CD-ROM drive can work properly, please connect it to the IDE port that is controlled by the Southbridge, not the GigaRAID controller). Then connect the power connector from your power supply to the hard drive(s). "*" Skip this step if you do not want to create RAID array on the IDE controller IDE RAID Drives Configuration (GigaRAID) -2- (2) Configuring GigaRAID controller mode and boot sequence in BIOS Setup You have to make sure whether the GigaRAID controller are configured correctly in system BIOS Setup and set BIOS boot sequence for the IDE RAID hard drive(s). [. . . ] And press any key to return to the Main Menu. This action completes RAID configuration. 6 Figure 6 IDE RAID Drives Configuration (GigaRAID) -6- Define RAID: The Define RAID selection allows you to create RAID set with several hard drives to mirror the data from a damaged RAID 1 (or RAID 0+1) hard drive to the new replacement hard drive. Press 2 in Main Menu and the Define RAID Menu as shown in Figure 7 will appear. Use ARROW keys to highlight through arrays and press ENTER after selecting an array. You will see the Define RAID SubMenu (Figure 8 on next page) from which you may configure the new RAID array. Figure 7 -7- IDE RAID Drives Configuration (GigaRAID) Ác Åé ¤¤ ¤å Define RAID Sub-Menu (Figure 8): Use the UP or DOWN ARROW key to move to an item and use SPACEBAR to cycle through options. Array Mode: Press SPACEBAR under this item to select RAID 0 (Striping) mode. In the following procedure, we will create a RAID 0 (Striping) array as an example. Block Size: If you select to create RAID 0 (Striping) or RAID 0+1 (Striping+Mirroring), you have to specify the block size. The block size options include 1KB, 2KB, 4KB, 8KB, 16KB, 32KB and 64KB. Assignment: Use the ARROW keys to move to the Assignment section of the desired hard drive and press SPACEBAR to change the Assignment option to Y. This action adds the drive to the RAID set. To successfully create a RAID array, you need to set at least two hard drives to Y status. You will see that the Drive No section displays the number of hard drives that are labeled with Y. Next, if you are sure to erase the old data in the hard drive, press Y to confirm (or N to cancel). Now, you should see "Functional" in the Status section, which indicates the RAID array is operational. Press ESC to return to the Define RAID Menu and you should see the functional RAID set (refer to Figure 9 on next page). Figure 8 IDE RAID Drives Configuration (GigaRAID) -8- Figure 9: Information about the RAID set. -9- IDE RAID Drives Configuration (GigaRAID) Ác Åé ¤¤ ¤å Delete RAID: Press 3 in Main Menu to enter the Delete RAID Menu (Figure 10). [. . . ] The installation utility will appear automatically. Step 2: Go to My Computer and right-click the CD-ROM drive icon and select Open (Figure 11). Figure 16 Step 3: Go to the BootDrv folder and look for an executable program named MENU. exe (Figure 17). Figure 17 IDE RAID Drives Configuration (GigaRAID) - 14 - Step 3: Double-click MENU. exe. An MS-DOS prompt screen similar to Figure 18 below will appear. Figure 18 Step 4: Insert an empty floppy disk. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GIGABYTE GA-8SQ800 ULTRA2

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual GIGABYTE GA-8SQ800 ULTRA2 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag