User manual GIGABYTE GA-9SISL

[. . . ] 1001 Intel® Atom® processor motherboard Copyright © 2014 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations:  For detailed product information, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Table of Contents Box Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 GA-9SISL Motherboard Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GA-9SISL Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 1 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1-1 1-2 1-3 Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Default setting is Disabled. ARI Forwarding AtomicOp Requester Enable AtomicOp Egress Blocking BIOS Setup - 40 - IDO Request Enable If supported by hardware and set to 'Enabled', this permits settings the number of ID-Based Ordering (IDO) bit (Attribute[2]) requests to be initiated. If supported by hardware and set to 'Enabled', this permits settings the number of ID-Based Ordering (IDO) bit (Attribute[2]) requests to be initiated. If supported by hardware and set to 'Enabled', this enables the Latency Tolerance Reporting (LTR) Mechanism. If supported by hardware and set to 'Enabled', this function will block forwarding of TLPs containing End-End TLP Prefixs. Default setting is Disabled. IDO Completion Enable LTR Mechanism Enable End-End TLP Prefix Blocking PCI Express GEN2 Device Register Settings Target Link Speed Clock Power Management If supported by hardware and set to 'Force to 2. 5 GT/s' for Downstream Ports, this sets an upper limit on link operational speed by restricting the values advertised by the Upstream component in its training sequences. Options available: Auto/Force to 2. 5GT/s/Force to 5. 0GT/s. If supported by hardware and set to 'Enabled', the device is permitted to use CLKREQ# signal for power management of link clock in accordance to protocol defined in appropriate from factor specification. If supported by hardware and set to 'Enabled', this will force LTSSM to send SKP Ordered Sets between sequences when sending Compliance Pattern or Modified Compliance Pattern. If supported by hardware and set to 'Disabled', this will disable the hardware's ability to change link width size reduction for the purpose of correcting unstable link operation. If supported by hardware and set to 'Disabled', this will disable the hardware's ability to change link speed rate reduction for the purpose of correcting unstable link operation. Default setting is Enabled. Compliance SOS Hardware Autonomous Width Hardware Autonomous Speed - 41 - BIOS Setup 2-2-3 Network Stack Network stack Enable/Disable UEFI network stack. Default setting is Enabled. Ipv4 PXE Support(Note) Ipv6 PXE Support(Note) (Note) This item appears when Network Stack is set to Enabled. BIOS Setup - 42 - 2-2-4 CSM Configuration Compatibility Support Module Configuration CSM Support Enable/Disable Compatibility Support Module (CSM) support. Upon Request: GA20 can be disabled using BIOS services. Always: Do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Options available: Force BIOS/Keep Current. Enabled: Allowed headless retry boot Options available: Enabled/Disabled. BIOS reaction on INT19 trapping by Option ROM Immediate: execute the trap right away. Postpone: execute the trap during legacy boot. Default setting is Immediate. CSM16 Module Version Gate20 Active Option ROM Messages INT19 Endless Retry INT19 Trap Response - 43 - BIOS Setup Boot option filter Determines which devices system will boot to. Options available: UEFI and Legacy/Legacy only/UEFI only. Default setting is UEFI and Legacy. Option ROM execution Network Controls the execution UEFI and Legacy PXE OpROM. [. . . ] Press Enter to configure the device as the boot-up drive. UEFI: Built-in in EFI Shell Press <Enter> on this item to Launch EFI Shell from filesystem device. BIOS Setup - 80 - 2-8 BIOS Beep Codes # of Beeps 5 Memory error during POST. Description - 81 - BIOS Setup 2-9 BIOS Recovery Instruction The system has an embedded recovery technique. [. . . ]