User manual GIGABYTE GA-K8N51PVMT-9

[. . . ] GA-K8N51PVMT-9 AMD Socket 939 Processor Motherboard User's Manual Rev. 1003 12ME-51PVMT9-1003R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-K8N51PVMT-9 Motherboard GA-K8N51PVMT-9 Oct. 18, 2005 Copyright © 2005 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] (Default value) Clear case open status at next boot. Case Opened If the case is closed, Case Opened will show "No. " If the case is opened, Case Opened will show "Yes. " If you want to reset Case Opened value, enable Reset Case Open Status and save the change to CMOS, and then your computer will restart. Current Voltage(V) VCORE / DDR Power / +3. 3V / +12V Detect system's voltage status automatically. System/CPU Temperature Detect system/CPU temperature automatically. System/CPU FAN Speed (RPM) Detect System/CPU fan speed status automatically. CPU Warning Temp. 60 o C / 140 o F 70 o C / 158 o F 80 o C / 176 o F 90 o C / 194 o F Disabled Disabled Enabled Monitor CPU temperature at 60o C / 140 oF. Monitor CPU temperature at 70o C / 158 oF. Monitor CPU temperature at 80o C / 176 oF. Monitor CPU temperature at 90o C / 194 oF. (Default value) Disable System/CPU fan stop warning function. (Default value) Enable System/CPU fan stop warning function. System/CPU FAN Stop Warning GA-K8N51PVMT-9 Motherboard - 42 - CPU Smart FAN Control (Note) Disabled Enabled Disable this function. (Default value) When this function is enabled, CPU fan will run at different speed depending on CPU temperature. Users can adjust the fan speed with Easy Tune based on their requirements. English (Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install. For more detailed information please check at the FAQ section on GIGABYTE's website. - 43 - BIOS Setup English 2-7 Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Frequency/Voltage Control CPU Frequency PCIE Clock K8 CPU Clock Ratio Display Output TV Mode Support Robust Graphics Booster [200. 0] [100Mhz] [Default] [RGB] [Disabled] [Auto] Item Help Menu Level : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Incorrect using these features may cause your system broken. For power end-user use only. CPU Frequency 200. 0~300. 0MHz Set CPU Frequency from 200MHz to 300MHz. PCIE Clock 100~145MHz Set PCIE Clock from 100MHz to 145MHz. K8 CPU Clock Ratio This setup option will automatically assign by CPU detection. The option will display "Locked" and read only or will not show up if the CPU ratio is not changeable. Display Output This feature RGB TV AUTO allows you to set signal output from the D-Sub(VGA) or S-Video(TV) port. (Default value) Set signal output from the S-Video port. The signal will output from S-Video if you connect the output device to the S-Video port. If there is no output device on the S-Video port, the signal will output from D-Sub. TV Mode Support Select the TV system, the options include: NTSC-M, NTSC-J, PAL-M, PAL-BDGHI, PAL-N and PAL-NC. (Default value) Robust Graphics Booster Select the options can enhance the VGA graphics card bandwidth to get higher performance. Auto Set Robust Graphics Booster to Auto. (Default value) Fast Set Robust Graphics Booster to Fast. Turbo Set Robust Graphics Booster to Turbo. GA-K8N51PVMT-9 Motherboard - 44 - 2-8 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Load Fail-Safe Defaults Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Fail-Safe DefaultsSave & Exit Setup (Y/N)?N Exit Without Saving : Select Item F10: Save & Exit Setup English Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Load Optimized Defaults Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?N Setup Save & Exit Exit Without Saving : Select Item F10: Save & Exit Setup Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. - 45 - BIOS Setup English 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup Enter Password: PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Change/Set/Disable Password When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]