User manual GIGABYTE GA-K8NE

[. . . ] GA-K8NE AMD Socket 754 Processor Motherboard User's Manual Rev. 2004 12ME-K8NE-2004R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-K8NE Motherboard GA-K8NE Sep. 20, 2005 Copyright © 2005 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] (Default value) Set K8 CPU Clock Ratio from x5 1000Mhz to x10 2000Mhz. Set CPU Spread Spectrum to Center Spread. (Default value) Set PCI-E clock from 100Mhz to 150Mhz. K8 CPU Clock Ratio Default x5 1000Mhz ~ x10 2000Mhz CPU Spread Spectrum Disabled Center Spread PCIE Clock 100Mhz ~ 150Mhz Robust Graphics Booster Select the options can enhance the VGA graphics card bandwidth to get higher performance. Auto Set Robust Graphics Booster to Auto. (Default value) Fast Set Robust Graphics Booster to Fast. Turbo Set Robust Graphics Booster to Turbo. DDR voltage control Please note that by overclocking your system through the increase of the DDR voltage, damage to the memory may occur. Normal Set DDR voltage control to Normal. (Default value) +0. 1V Set DDR voltage control to +0. 1V. +0. 2V Set DDR voltage control to +0. 2V. - 43 - BIOS Setup English 2-8 Top Performance CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management SetupTop Performance PnP/PCI Configurations Disabled. . . . . . . . . . . . . . . . . . . . . . . . . [ ] PC Health Status Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . [ ] MB Intelligent Tweaker(M. I. T. ) Esc: Quit F8: Q-Flash Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup : Move ENTER: Accept ESC: AbortLoad Fail-Safe Defaults If you wish to maximize the performance of your system, enable "Top Performance. " Disabled Disable this function. (Default Value) Enabled Enable Top Performance function. "Top Performance" will increase H/W working speed. Different system configuration (both H/W component and OS) will effect the result. For example, the same H/W configuration might not run properly with Windows XP, but works smoothly with Windows NT. Therefore, if your system is not perform enough, the reliability or stability problem will appear sometimes, and we will recommend you disabling the option to avoid the problem as mentioned above. 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash Load Optimized Defaults : Select Item F10: Save & Exit Setup Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?N Save & Exit Setup Exit Without Saving Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. GA-K8NE Motherboard - 44 - 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup Enter Password: PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Change/Set/Disable Password Top Performance Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving English When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]